Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider a thin ring of radius a with uniform charge density and total charge Q. The ring is cut in half across the diameter and the two halves superimposed to double the effective charge density. Calculate the electric field at a point 4a from the ring along the x-axis with the ring in the y-z plane and the center of the arc at the origin. The half-ring is symmetric about the z-x plane extending only in the positive z-direction.
Consider a thin annular disk of outer radius 2a and inner radius a with a uniform charge density,s. The total charge is Q. (a) Calculate the field on one side of the disk as a function of the distance x from the disk along the centerline. (b) Make a plot of the dimensionless field strength, E?o /s , as a function of dimensionless distance x/a from zero to 5.
A piston-cylinder device contains carbon dioxide CO2 (molar mass = 46 g/mol) as shown in the figure. The cross-section area of the piston is 0.25 m2 and the initial cylinder height is 50 cm. CO2 is initially at 40 bar and 500 oC (state 1).
An incident -ray photon is scattered from a free electron that is initially at rest. The photon is scattered straight back at an angle of 180 degrees from its initial direction. The wavelength of the scattered photon is 9.00×10^-2 nm.
An input signal of 10V at 0o and a frequency of 1592 Hz is applied to a series RLC circuit with resistor R = 100 ohm, inductor L = 40 mH, and capacitor C = 0.5 F. The value of the total circuit complex impedance is
Consider a Si p-n junction at room temperature. If the doping concentrations are NA=1016 cm-3 and ND=1015 cm-3, what is the depletion width also known as space charge width Also find the maximum electric field.
The collector current was measured for different values of load resistance. It was noticed that the collector current was pretty much constant for the first 1900 ohms and then it fell drastically.
This bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F=0.55 kN and T=25.N.m. Use both the maximum-shear theory and the distortion-energy theory to design the bar diameter D.
A 3.3V, 30 A dc power supply is to be designed with a ripple of less than 2.5%. Assume that a half-wave rectifier circuit (60 Hz) with a capacitor filter is used.
A very long cylinder of radius 2.00 cm carries a uniform charge density of 1.50 nC/m. Taking the reference level for the zero of potential to be the surface of the cylinder, find the radius of equipotential surfaces having potentials of 10.0V, 20...
A p-type wafer has a diffused Phosphorous n-type junction with a junction depth of 0.15µm. a) If the wafer (no pre-existing oxide) is to be oxidized at 1000 C for two hours to form a ‘dense.
Determine the probability that the receiver correctly receives the codeword for the first time on the k-th transmission. Also determine the average number of transmissions until the receiver correctly receives the codeword.
Determine zero-input response of (D2+4D+40)y(t)=(D+2)x(t) with initial condition y0(0)=2 & dy0(0)/dt=16.78.
A filter with a great deal of attenuation must be placed in an amplifier chain. Ignoring all considerations other than the desire to minimize noise figure, would it be preferable to put the filter before or after a low noise amplifier Why
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd