Calculate a linear least-squares equation for the data

Assignment Help Mechanical Engineering
Reference no: EM131083408

The volumes of a solution containing 1.10 ppm of Zn2+ shown in the table were pipetted into separatory funnels, each containing 5.00 mL of an unknown zinc solution. Each was extracted with three 5-mL aliquots of CCI4 containing an excess of 8-hydroxyquinoline. The extrats were then diluted to 24.0 mL and their fluorescence measured with a fluorometer. The results were the following.

2049_8ebe62bd-6271-402f-9981-1c083e56c67a.png

(a) Construct a working curve from the data.

(b) Calculate a linear least-squares equation for the data.

(c) Calculate the standard deviation of the slope and intercept and the standard deviation about regression.

(d) Calculate the concentration of zinc in the sample.

(e) Calculate a standard deviation for the result in part (d).

Reference no: EM131083408

Questions Cloud

What interest rate level would a new equilibrium occur : At approximately what interest rate level would a new equilibrium occur? What curve or curves would have to shift in order for this equilibrium to occur? What would happen to the economy in regards to the money market and output market if the governm..
What is equilibrium price and quantity of surfboards sold : Assume that the demand for surfboards in a given town is P = 100-4Q and the supply for surfboards in that same town is given by P = Q. What is the equilibrium price and quantity of surfboards sold in this town? Now assume that the EPA has found that ..
What is a potential benefit of supply chain visibility : What is a potential benefit of supply chain visibility and what was the limitation of Excel-based data analytics at Safeway?
Prepare a post closing trial balance as of january : Prepare a post closing trial balance as of January 31, 2010 on the sheet. Prepare the income statement, statement of retained earnings and classified balance sheet as of January 31, 2010. Prepare the statements on the sheets.
Calculate a linear least-squares equation for the data : Calculate a linear least-squares equation for the data.
Problem regarding the correct mathematical symbols : Answer will not have exact numeric dimensions but rather three algebraic terms that represent them. Must show how the problem was solved by using correct mathematical symbols and thoroughly explaining with words in each step
Why is a green filter used : Why is a green filter used?
Length of the diameter of the circle : What is the length of the diameter of the circle?
What is a rational expression : What is a rational expression?  Please provide 1 addition and 1 subtraction examples where the denominators are the same and at least one example where the denominators are different.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd