User Account

All Pages

Bullet a from west with a mass of 175g and speed of 550ms

Assignment Help Mechanical Engineering
Reference no: EM13345227

Bullet A from west with a mass of 175g and speed of 550m/s and bullet B from east with a mass of 150g and speed of 200m/s moves towards to a block that having mass 12kg. If the bullets stick to the block and they move together find the velocity of the final system and find the total impulse of each bullet if the movement takes 0.5s before coming to a stop.

Reference no: EM13345227

Questions Cloud

Hot water at 90c enters a 15-m section of cast iron pipe : hot water at 90c enters a 15-m section of cast iron pipe whose inner diameter is 5.3 cm at an average velocity of
Magnesium has three naturally occurring isotopes 24mg : magnesium has three naturally occurring isotopes 24mg isotopic mass 23.9850 amu abundance 78.99 25mg isotopic mass
The mass of the flask is measured when the outside of the : the mass of the flask is measured when the outside of the flask is wet. outside of the flask is dried before the mass
A helium balloon lifts off at 10 atm and 25 degc with a : a helium balloon lifts off at 1.0 atm and 25 degc with a volume of 1.5 x 103 l. at an altitude of 21 km the temperature
Bullet a from west with a mass of 175g and speed of 550ms : bullet a from west with a mass of 175g and speed of 550ms and bullet b from east with a mass of 150g and speed of 200ms
Determine the gram formula mass of the compound : determine the gram formula mass of the compound
Use charless law to calculate the volume the gas will : a fixed quantity of gas at 25degc exhibits a pressure of 724 torr and occupies a volume of 5.90 l.a use boyles law to
At what mz values would you expect to observe the three : the mass natural abundance of the isotopes h and d are 99.985 and 0.015 respectively. the mass natural abundance of
Elemental exonium not a real element consists of two major : elemental exonium not a real element consists of two major isotopesabundance mass59 94 amu41 112 amuwhat is the atomic

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the values of t

the motion of a particle is defined by the position vector r=a(cos t + t sin t)i + A(sin t-t cos t)j, where t is expressed in seconds. Determine the values of t for which the position vector and acceleration are.

  Explain the compression ratio of an air-standard otto cycle

The compression ratio of an air-standard Otto cycle is 9.5. Prior to the isentropic compression process, the air is at 100 kPa, 17 C, and 600 cm2

  Problem 1 the u-tube manometer shown below is open to the

problem 1 the u-tube manometer shown below is open to the atmosphere and partiallynbspfilled with water so that the

  Determine the magnitude of the load p

Knowing that the modulus of elasticity of brass is 105 GPa, determine the magnitude of the load P for which the deflection of the plug is 1,25 mm downward.

  Overlay the frequency spectrum of the excitation

Sketch the frequency response of the system. Overlay the frequency spectrum of the excitation and as you start the system up, increasing Ω from 0 to 60 rpm, what speeds are most likely to excite large amplitude response? Why?

  Determine the coordinates xc and yc of the point

determine the coordinates xc and yc of the point where the resultant load must act in order to produce uniform normal stress in the column.

  Water flows through a pipe at an average temperature of

water flows through a pipe at an average temperature of t70degc. the inner and outer radii of the pipenbspare r16cm and

  Determine the force exerted by each cylinder

determine the force exerted by each cylinder in raising the crate for u = 60°, a 5 0.70 m, and L = 3.20 m. Show that the result obtained is independent of the distance d.

  Compare and comment on the results obtained

Using the required parameters for a typical large size car* and an appropriate frontal Quarter-Car model.

  Define the temperature of the water drops

The temperature of the water drops to 260 F as a result of heat transfer to the surroundings. Determine the final pressure in the tank?

  Air at the rate of 18 kgs is drawn into the compressor of a

air at the rate of 18 kgs is drawn into the compressor of a jet engine at 55 kpa and -23oc and is compressed reversibly

  Determine the normal stress in the central portion of link

the link DE is 3mm thick and 25 mm width,determine the normal stress in the central portion of the link.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd