Briefl y describe what an eprom is and when it is employed

Assignment Help Electrical Engineering
Reference no: EM131171698

EPROM

a. Briefl y describe what an EPROM is and when it is employed.

b. What are its basic differences with respect to OTP-ROM and MP-ROM?

Reference no: EM131171698

Questions Cloud

Deposited at the end of every six months : Suppose $693 is deposited at the end of every six months into an account earning 6.05% compounded semi-annually. If the balance in the account four years after the last deposit is to be $30 600.00, how many deposits are needed? Please show all wo..
Identify the point of view used in the narration : Identify the point of view used in narration. Discuss how this point of view affects your reading and interpretation of the story. How might a different type of narration (point of view) alter the meaning of the story?
Who be looking over the shoulder of the project manager : Who should be "looking over the shoulder" of the project manager to make sure that the work and requests are also in the best interest of the company?
Principal of the loan : A loan is repaid by making payments of $5000.00 at the end of every six months for fourteen years. If interest on the loan is 8% compounded quarterly, what was the principal of the loan? Note: Different periods of compounding and repayments.
Briefl y describe what an eprom is and when it is employed : What are its basic differences with respect to OTP-ROM and MP-ROM?
Project driven and non project driven organizations : Explain how career paths and career growth can differ between project-driven and non-project-driven organizations.
Revolutions per minute : Shirley is on a Ferris wheel which spins at the rate of 3.8 revolutions per minute. The wheel has a radius of 45 feet, and the center of the wheel is 57 feet above the ground. After the wheel starts moving, Shirley takes 13 seconds to reach the to..
Write an in-depth analytical essay using your own ideas : In a 4-page (1,200-word) literary analysis, write an in-depth analytical essay using your own ideas plus supporting evidence from the text, such as quotations, paraphrases, and summaries.
Are they conceptually intended for the same applications : Briefl y describe the main conceptual differences between DRAM and SDRAM.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What percentage of accounts are savings or opened

In a bank, among the accounts opened before 2005, 40% are saving accounts, 20% are chequing accounts and rest are mutual fund accounts. These numbers for accounts opened on or after 2005 are: 30% saving accounts,

  Calculate the voltage across 480 v winding

A single phase two winding transformer having rating: 20 KVA,480/120 V, 60 Hz A source connected to the 480 V winding supplies an impedance load connected to 120 V winding. The load absorbs 15 KVA at 0.8 pf lagging when load voltage is118 V.

  To investigate the improvement produced in density matching

Using computer simulations, compare the density matching produced by the conscience algorithm with that produced by the SOM algorithm. For the SOM algorithm use η = 0.05, and for the conscience algorithm use B = 0.0001, C = 1.0, and η = 0.05.

  Determine which wafer will exhibit the larger resistivity

(a) An average hole velocity of 10^3 cm/sec results when 2 v is appliedaccross a 1 cm-long semiconductor bar. What is the mobilityof the bar (b) name the two dominant carrier scattering mechanisms innondegenerately doped semiconductors of device qu..

  Calculate sending-end power if receiving-end voltage given

Resistance=0.09ohm/km Inductance=1.4mH/km Capacitance=8.8x10-3 uF/km. Calculate the sending-end power if the receiving-end voltage is 132kV and the receiving-end power is S2=100+j60 MVA. Assume a pi-equivalent circuit.

  What is thermally generated density of electrons and holes

Silicon, originally intrinsic, is doped with 4*10^16 /cm^3 of arsenic atoms at room temperature. a) What proportion of the silicon atoms have been replaced by arsenic atoms b) What is the thermally generated density of electrons and holes

  Determine the position x and the tension in the cord

Determine the position x and the tension in the cord that is required for equilibrium. The cord passes through the smooth ring at B and has an unstretched length of 6ft and stiffness of k = 50lb/ft.

  Implement boolean functions using a decoder

Implement the following boolean functions using a 3x8 decoder constructed with NAND gates and three external NAND or three external AND gates. F1(A,B,C) = m(2,4,7) F2(A,B,C) = m(0,3) F3(A,B,C) = m(0,2,3,4,7)

  Plot the input and output constant-gain circles

Design an amplifier for a power gain of 15dB at 3 GHz if 1. Plot the input and output constant-Gain circles. 2. Find the input and output matching networks. use L C components.

  Find the voltage gain realized

A transconductance amplifier with Ri = 2 kΩ, Gm = 40 mA/V , and Ro = 20kΩ is fed with a voltage source having a source resistance of 2kΩ and is loaded with a 1kΩ resistance. Find the voltage gain realized (from the source internal voltage to the o..

  How to calculate and find the value of ceramic

How to Calculate and Find the value of Ceramic and Non-Polarized Capacitors? (with an example of capacitors that have general value between 1 µF-1pF)

  Determine what is the capacitance of the parallel capacitor

A capacitor is formed by two metal parallel plates with the dimensions 210 mm x 210 mm separated by the gap of 1.2 um (u=micro) filled with dielectric material with relative dielectric permittivity 3.8.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd