User Account

All Pages

Block b is attached to the 20mm inner diameter block a

Assignment Help Mechanical Engineering
Reference no: EM13636868

Block A is dropping at a velocity of 600mm/sec and acceleration of 100mm/sec^2. It is attached directly to an inner diameter of 30mm and an outer diameter of 40mm. The 40mm outer diameter pulley is connected to another pulley with an outer diameter of 50mm and an inner diameter of 20mm. Block B is attached to the 20mm inner diameter. Block A drops vertically and block B travels horizontally. Determine the linear velocity and the acceleration of block B.

Reference no: EM13636868

Questions Cloud

The financial industry earnings per share last year were 3 : the financial industry earnings per share last year were 3. this year earnings per share in 10 financial companies were
A peroxidase enzyme isolated from human red blood cells : a peroxidase enzyme isolated from human red blood cells was found to contain 0.29 selenium. what is the minimum molar
The mass of an atom oscillating at a frequency of 86 x : the mass of an atom oscillating at a frequency of 8.6 x 1011hz in its lattice is 1.2 x 10-26 kg. if the amplitude of
A small amount of the solid mgso4 7h2o is put in a : a small amount of the solid mgso4 7h2o is put in a crucible. the solid is gently heated by a bunsen burner until all
Block b is attached to the 20mm inner diameter block a : block a is dropping at a velocity of 600mmsec and acceleration of 100mmsec2. it is attached directly to an inner
Te equation of oscillation of a mass-spring system is xt : the equation of oscillation of a mass-spring system is xt 0.3cos4t - 0.7 where x is in meters and t in seconds. the
How would the wheel diameter and the volumes of the : the minto wheel is a power-producing device activated by evaporating and condensing a work substance. the only energy
Construct the confidence interval for the population : 1. construct the confidence interval for the population mean?c0.95 xsamplemean 16.1 s8.0 and n90a 95 confidence
What amount of solid naoh must be added to 10 l of a 15 m : what amount of solid naoh must be added to 1.0 l of a .15 m h2co3 solution to produce a solution with h 3.5x10-11 m?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Water flowing in a line at 60 lbfin2 saturated vapor is

water flowing in a line at 60 lbfin2 saturated vapor is taken out through a valve at 14.7 lbfin2. what is the

  If both streams enter the mixing chamber at the same mass

water at 50 degrees farheneit and 50 psia is heated in a chamber by mixing it with saturated water vapor at 50 psia. if

  Determine the magnitude of its total accleration

determine the magnitude of its total accleration when (a) t=0 and (b) t=2 Whats the solution.

  Find the rate of change of the density in the tire

Air at 250 kPA and 15C is being forced into a tire, which has a volume of 0.5m^3, at a velocity of 60 m/s through a 6 mm opening. Find the rate of change of the density in the tire.

  Consider a 1000-w iron whose base plate is made of

consider a 1000-w iron whose base plate is made of 0.5-cm-thick aluminium alloy 2024-t6 p2771 kgm3 and cp 875 jkg c.

  The temperature disribution along a cylindrical rod of

the temperature disribution along a cylindrical rod of length l is given by the function txaxlbx2lcsinpixlde-alphaxl 0

  Part-1suppose that a simple pendulum is attached to our

part-1suppose that a simple pendulum is attached to our spring-damper-mass system. a simple schematic of the model is

  A team of engineers are required to examine the viv of

offshore oil drilling model the large portion of an offshore oil drill is a long cylinder diameter d and length l that

  Which is supported on the opposite side is the engine mount

a 2 cm by 2 cm by 2 cm rubber engine mount e 30 mpa poisson ratio 0.4999 must support a 300 kg motor. what maximum

  The wafer is insulated at the bottom a calculate the

an annealing process shown uses a hot plate operating at an elevated temperature of 635 c. the wafer initially at a

  A exit p2 - 147 psia v2 2677 ft3lb and u2 10775 btulb

there are supplied to a nozzle 2400 lbhr of steam at an absolute pressure of 200 psia. at the entrance v1 6000 ftmin

  The outisde tempature drops to -27 celsius determine the

a heat pump is to be used to heat a building during the winter. the building is to be maintained at 24.2 celsiius at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd