At what depth should it be to avoid cavitation at 30 m/s

Assignment Help Mechanical Engineering
Reference no: EM131150154

A torpedo 8 m below the surface in 20°C seawater cavitates at a speed of 21 m/s when atmospheric pressure is 101 kPa. If Reynolds number and Froude number effects are negligible, at what speed will it cavitate when running at a depth of 20 m? At what depth should it be to avoid cavitation at 30 m/s?

Reference no: EM131150154

Questions Cloud

What method of job analysis is josh using : Based on your text, newspaper advertisements typically ask the applicant to respond in one of four ways. Which of the following is NOT one of the four ways?
Can this data be used to correlate an oxygen tank : If so, estimate the oxygen mass flow if the tank conditions are 300 kPa and 450 K, with a nozzle diameter of 3 cm
What court will have jurisdiction over tanya suit : What court will have jurisdiction over Tanya's suit? Why? Is the Confusion statute constitutional? Discuss your legal reasoning. What provisions of the U.S. Constitution will be applied by a court to determine the statute's validity
Formulate a plan to effectively integrate this product : You have been appointed as a new product manager with Samsung and have been tasked to introduce the latest smartphone in a new country. Choose and research a country other than the United States, and then formulate a plan to effectively integrate ..
At what depth should it be to avoid cavitation at 30 m/s : At what depth should it be to avoid cavitation at 30 m/s?
Case for critical analysis : Read the “Case For Critical Analysis” Abrahams Grocery at the end of Chapter 7. Based on the information available in the case, discuss what type of organizational structure was being used at Abrahams BEFORE the consultant was brought in. Discuss wha..
Provide your analysis of the roles heredity : Provide your analysis of the roles heredity, the environment, and epigenetics play in the development of personality. Discuss how heredity and the environment might affect personality disorders. This section will be approximately three to five p..
Identify a disease which is caused by a mutation : Next identify a disease, which is caused by a mutation, and then describe the biological basis of your chosen disease. In your response be sure to note the exact disease causing mutation.
Minimum slack rule is probably best overall priority rule : The minimum slack rule is probably the best overall priority rule because of ALL the following EXCEPT:

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd