At the beginning of compression p1 85 kpa and t1 305 k

Assignment Help Mechanical Engineering
Reference no: EM13612893

An air-standard Otto cycle has a compression ratio of 7.5. At the beginning of compression, P1 = 85 kPa and T1 = 305 K. The mass of air is 2 g. and the maximum temperature in the cycle is 960 K. Determine:

(a) the heat rejection, in kJ.

(b) the net work, in kJ.

(c) the thermal efficiency.

(d) the mean effective pressure, in kPa.

Reference no: EM13612893

Questions Cloud

A bar of steel 3 in 762mm in diameter is to be machined at : 1 a bar of steel 3 in 76.2mm in diameter is to be machined at 90 fpm 0.5 msec. what spindle speed should be
Calculate the limiting visual brightness in magnitudes for : a calculate the limiting visual brightness in magnitudes for naked eye viewing through a 10-m telescope. assume the eye
If a general linear programming problem can also be : 1. the complementary slackness principle states that either there is zero slack on a constraint or the reduced cost is
Each two years a man trades his car for a new car if he has : each two years a man trades his car for a new car. if he has a ford he trades it for mercedes-benz . if he has a
At the beginning of compression p1 85 kpa and t1 305 k : an air-standard otto cycle has a compression ratio of 7.5. at the beginning of compression p1 85 kpa and t1 305 k.
A box contains 100 bulbs 2 of which are defective and the : a box contains 100 bulbs 2 of which are defective and the remaining are non-defective. one bulb is selected after
The solar constant is the flux of the suns radiation at the : the solar constant is the flux of the suns radiation at the top of the earths atmosphere. calculate its value assuming
A box contains one twenty-dollar bill and four one-dollar : a box contains one twenty-dollar bill and four one-dollar bills. two bills are randomly chosen one at a time without
The condenser operates at 10 kpa determinea the mass flow : a steam power plant implements an ideal reheat rankine cycle. steam enters the inlet of the high-pressure turbine at 8

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Air enters a one-inlet one-exit control volume at 6 bar 500

air enters a one-inlet one-exit control volume at 6 bar 500 k and 30 ms through a flow area of 28 cm2. at the exit the

  Determine the height to which the pulley is lifted

a simple pulley with the given radius r used to lift heavy objects is positioned 10 feet above ground level. Given that the pulley rotates theta degrees, determine the height to which the pulley is lifted.

  Determine the moment of the force

A 90-N force is applied to the control rod AB as shown. Knowing that the length of the rod is 225 mm, determine the moment of the force about point B by resolving the force into horizontal and vertical components.

  The steel pipe is filled with concrete and subjectednbspto

the steel pipe is filled with concrete and subjectednbspto a compressive force of 80 kn. determine the stress innbspthe

  Determine the following a pressure psi at each state b mass

a closed rigid tank contains 5 lbm of a two phase mixture of water initially at 260degf with a quality of 0.6. heat

  A diesel engine uses 544 kg of fuel oilh of calorific

a diesel engine uses 54.4 kg of fuel oilh of calorific value 45 mjkg. the thermal efficiency of the engine is 25.

  Determine the range of back pressure over which

A) A huge reservoir of air supplies a converging-diverging nozzle with throat and exit areas of 10 cm^2 and 25 cm^2 respectively. The reservoir pressure and temperature are 150 kPa and 20C. Determine the range of back pressure over which

  Determine the total electrical work the heat pump can

a carnot heat pump is to be used for heating house in winter. the house temperature is set at 25oc. one day the outdoor

  The pin is released which allows the piston to move

a piston held by a pin in an insulated cylinder shown in figure above right contains 2 kg water at 100c quality 98. the

  Compute the lift l and drag d experienced by the aircraft

the 30 mg aircraft is climbing at the angle theta15 with a thrust t of 180 kn. at the instant shown its speed is 300

  A heat exchanger is to be designed to condense 1100 kghr of

a heat exchanger is to be designed to condense 1100 kghr of steam ay 150 kpa. for this purpose cooling water at 50

  Find the magnitude of the average velocity

Remember that velocity is a vector quantity so find the magnitude of the average velocity and the angle of average velocity from the horizon

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd