At steady state the cycle develops 40 kw of power with a

Assignment Help Mechanical Engineering
Reference no: EM13612264

A power cycle operates between a high temperature reservoir (at TH K) and a low temperature reservoir at TC = 280 K. At steady state, the cycle develops 40 kW of power with a heat input of 56.67 kW from the high temperature reservoir. Determine the minimum theoretical value of TH required for operating this cycle by comparing it to Carnot efficiency.

Reference no: EM13612264

Questions Cloud

A soccer player kicks the ball toward a goal that is 130 m : a soccer player kicks the ball toward a goal that is 13.0 m in front of him. the ball leaves his foot at a speed of
Draw and label the t-s diagram for the ideal rankine cycle : water is the working fluid in an ideal rankine cycle. superheated vapor enters the turbine at 8 mpa 450 degc. the
If the company uses the double-declining-balance method of : flip company purchased equipment on january 1 2011 for 90000. it is estimated that the equipment will have a 5000
A calculate the distance along the ground measured from a : an airplane with a speed of 80.0 ms is climbing upward at an angle of 62.4 deg with respect to the horizontal. when the
At steady state the cycle develops 40 kw of power with a : a power cycle operates between a high temperature reservoir at th k and a low temperature reservoir at tc 280 k. at
The rocket attains its launch speed in a negligibly short : a rocket is fired at a speed of 93.0 ms from ground level at an angle of 61.0 deg above the horizontal. the rocket is
Prepare journal entries to record the following : prepare journal entries to record the following transactions entered into by flip company 2012 june 1 received a 10000
An eagle is flying horizontally at 55 ms with a fish in its : an eagle is flying horizontally at 5.5 ms with a fish in its claws. it accidentally drops the fish. a how much time
If the power generated by the turbine is 4 mw determine the : steam expands in a turbine steadily at a rate of 25000 kgh entering at 6 mpa and 450degc and leaving at 20 kpa as a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the minimum no of teeth required on pinion in

determine the minimum no of teeth required on pinion in order to avoid interference which is to gear with 1 a wheel to

  What dielectric constant must the material between the plate

A simple plate capacitor can store 6.5x10^-5 C at a potential of 10000 V. what dielectric constant must the material between the plates have if their area is 6.0x10^-5 m2 and they are 0.16 mm apart?

  Find the final condition of steam

Steam at 10bar and 0.95 dry flows at 130 m/sec in a pipe. It is throttled to 8 bar and the flow rate is 12 kg/sec. Assuming velocity in the pipe on the down stream side of the valve is 160 m/sec. Find the final condition of steam and the pipe diam..

  How do you calculate the strain of a solid cantilever

how do you calculate the strain of a solid cantilever bending beam fixed at one end if given curvature of 0.0243 m and

  A city water main to the water tower and is 794 feet above

based solely on static elevation head if the water level in a city water tower is 860 feet above sea level and the

  Determine the maximum speed

Determine the maximum speed at which the car with mass can pass over the top point A of the vertical curved road and still maintain contact with the road.

  Determine a the temperature of the air at the compressor

n air compressor operates at steady state with air entering at p1 1 bar t1 17 c and exiting at p2 5 bar. the air

  Who might it have collaborated with

What would have been the advantages or disadvantages of Tata collaborating with another automaker on the Tata? Who might it have collaborated with?

  Is the displacement field compatible

A body with a plane stress field has material properties E, ν and has the following displacement field

  What is the air temperature at the stagnation point

A high performance F-16 fighter is flying at Mach 0.96 at sea level. What is the air temperature at the stagnation point at the leading edge of the wing?

  What is the number of turns per meter of length of the

the magnetic field produced by the solenoid in a magnetic resonance imaging mri system designed for measurements on

  Draw a central cross-section of the heat exchanger

Derive at least four concept designs to satisfy the given specification - draw a central cross-section of the heat exchanger

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd