User Account

All Pages

Assuming there is no friction what will be the final height

Assignment Help Mechanical Engineering
Reference no: EM13628235

A solid, cylindrical workpiece made of 5052-O Aluminum is 12 cm high and 8 cm in diameter. Assuming there is no friction, what will be the final height of the workpiece if a 3 MN forging press is used, and the flow stress is estimated to be 85 MPa?

Reference no: EM13628235

Questions Cloud

A 120-m long steel wire has a coefficient of linear : a 120-m long steel wire has a coefficient of linear exspansion of 11x10-6 celcius. give its change in length as the
Describe the type i and type ii errors with your study what : in a recent shipment of insulin syringes hospital administrators discovered eight percent were unusable due to defects.
A 120-m long steel wire has a coefficient of linear : a 120-m long steel wire has a coefficient of linear exspansion of 11x10-6 celcius. give its change in length as the
An independent-measures research study uses two samples : an independent-measures research study uses two samples each with n 12 participants. if the data produce a t statistic
Assuming there is no friction what will be the final height : a solid cylindrical workpiece made of 5052-o aluminum is 12 cm high and 8 cm in diameter. assuming there is no
Suppose 25 kg of 32 deg c water is mixed with 93 kg of 65 : suppose 2.5 kg of 32 deg c water is mixed with 9.3 kg of 65 deg c water. if no heat is lost in this system then what is
Using both graphical and analytical methods in assessing : the following linear failure envelopes for a rock mass are givenintact rockfriction angle 350cohesion 900 psitension
A 900 kg crate is on a rough surface inclined at 30 degrees : a 900 kg crate is on a rough surface inclined at 30 degrees. a constant force p7200n is applied horizontally to the
The table below contains profit projections for various : the table below contains profit projections for various decisions to be made by the university. the associated

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The amount of energy required to bring the vehicle to a

consider a 1500 kg vehicle traveling at some unknown velocity and suddenly the brakes are applied and the vehicle is

  Consider a building whose annual air conditioning load is

consider a building whose annual air conditioning load is estimated to be 120000 kwh in an area where the unit cost of

  If the force exerted on cable ab by the motor is f 100t32 n

if the force exerted on cable ab by the motor is f 100t32 n where t is in seconds determine the 50-kg crates velocity

  A 12 kn force is exerted on a rocker arm the moment of

a 12 kn force is exerted on a rocker arm. the moment of inertia i of the crosssectionnbspwith respect to the

  Calibrated vibrometer output indicates a velocity amplitude

the waveform from a mechanical vibration is sensed by a velocity-sensitive vibrometer. the oscilloscope trave indicates

  The heat transferred to the condenser cooling water and the

1. steam is supplied dry saturated at 40 bar to a turbine and the condenser pressure is 0.035 bar. if the plant

  Knowing that it strikes the water 4 s after release

a stone is thrown vertically upward from a point on a bridge located 40 m above the water. knowing that it strikes the

  The tubes have center to center distance of 15 inches in

an in-line tube bank is constructed of 1 inch diameter tubes with 15 rows transverse to the flow 7 rows in the floe

  Explain from an atomic structure point of view why metals

1. in selecting the materials for keyboards terminals and other computer equipment that house the electronic components

  Draw the stress distribution along the walled thickness

Draw the stress distribution along the walled thickness and discuss whether the composite with the applied pressure is safe or not by using von-Mises and Tresca theory.

  Define and design a hollow steel shaft to transmit

Hollow shaft transmitting power with shear limits. Design a hollow steel shaft to transmit 300 hp at 75 rpm without exceeding a shear tress of 8000 psi. Use 1.2:1 as the ratio of the outside diameter to the inside diameter.

  Two kg of saturated liquid water at 1 bar is compressed to

two kg of saturated liquid water at 1 bar is compressed to 25 bar and 100degc in a water pump. determine the change in

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd