Assuming the process is working correctly draw and label a

Assignment Help Mechanical Engineering
Reference no: EM13637454

A stream of humid air containing 1.00 mole% water vapor and the balance dry air is to be humidified to a water content of 10.00 mole% water vapor. To achieve this liquid water is fed through a flow meter and evaporated into the air stream. The flowmeter reading R is 95. The only calibration data available are that readings of R = 15 and R = 50 correspond to liquid water flow rates of 40 ft3/hr and 96.9 ft3/hr, respectively.

a. Assuming the process is working correctly, draw and label a flow sheet, do a degree of freedom analysis, and determine the molar flow rate of humid air (lbmole/hr).

b. If it were found that the outlet air actually contained 7% water instead of the desired 10% list reasons why this might be so, concentrating on assumptions made in part a) above that might not be true in "real life."

Reference no: EM13637454

Questions Cloud

An artificial kidney is a device that removes water and : an artificial kidney is a device that removes water and waste products from the blood. one kind of artificial kidney is
A baseball thrown from the outfield is released from : a baseball thrown from the outfield is released from shoulder height at an initial velocity of 29.4 ms at an initial
Bacl2nbsp na2so4nbspharrbaso4nbsp nacl- gravimetic : bacl2nbsp na2so4nbspharrbaso4nbsp nacl- gravimetic determination of sulfate1 explain why adding an excess of
A study of the influence of corrosion inhibitor on the : a study of the influence of corrosion inhibitor on the failure of aluminum-wired twist-on connections the data obtained
Assuming the process is working correctly draw and label a : a stream of humid air containing 1.00 mole water vapor and the balance dry air is to be humidified to a water content
John throws a baseball from the outfield from shoulder : john throws a baseball from the outfield from shoulder height at an initial velocity of 29.4 ms at an initial angle of
Bacl2nbsp na2so4nbspharrbaso4nbsp nacl-gravimetric : bacl2nbsp na2so4nbspharrbaso4nbsp nacl-gravimetric determination of sulfate1 a procedure similar to the described in
A bolt comes loose from underneath an elevator that is : a bolt comes loose from underneath an elevator that is moving upward at a speed of 4.5 ms. the bolt reaches the bottom
Calculate the required oxygen flow rate in molhr and the : a mixture of methane and air is flammable only if the mole percent of methane is between 5 and 15. a mixture containing

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd