Assuming that the bolt will be allowed to cool until 21

Assignment Help Mechanical Engineering
Reference no: EM13618369

A spare pressure vessel flange bolt is discovered inside the reactor shroud during a refueling outage of a nuclear power plant. The bolt has a mass of 250 grams and has the following elemental composition (by weight): Fe-80%, Ni-19%, Mn-0.5%, Cr-0.5%. The bolt was exposed to a mean thermal neutron flux of 2x10^12 n/cm^2s during the 3 years that it was in the reactor. Assuming that the bolt will be allowed to cool until 21 days into the outage, find the following;

a)The primary radioisotopes and activities of each in the bolt.
b)The approximate dose rate at a distance of 1m from the unshielded bolt
c)The amount of water necessary between the bolt and a technician to reduce this dose rate to 25 mrem/hr.

Reference no: EM13618369

Questions Cloud

The mass of the bullet is 109 g the mass of the block is 88 : a heavy wooden block rests on a flat table and a high-speed bullet is fired horizontally into the block the bullet
Find the sample size needed to estimate the percentage of : find the sample size needed to estimate the percentage of adults who have consulted fortune tellers. use a 0.03 margin
Determine the final temperature in the tank the mass of : a 0.4m3 rigid tank initially contains refrigerant-134a at 14 degree c. at this state 70 of the mass is in the vapour
A find the direction of motion of the cue ball after the : in a pool game the cue ball which has an initial speed of 8.0 ms make an elastic collision with the eight ball which is
Assuming that the bolt will be allowed to cool until 21 : a spare pressure vessel flange bolt is discovered inside the reactor shroud during a refueling outage of a nuclear
The second acquisition target is a privately held company : a. the second acquisition target is a privately held company in a growing industry. the target has recently
Research and summarize the concept of the quantum computer : research and summarize the concept of the quantum computer and explain the concept of the qubit as opposed to the
One of the issues facing organizations is increasing : one of the issues facing organizations is increasing biodiversity throughout the organization. once of the ways to
A1300- kg car rolling on a horizontal surface has speed v : a 1300- kg car rolling on a horizontal surface has speed v 60kmh when it strikes a horizontal coiled spring and is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd