Assume the drainpipes are the same height as the building

Assignment Help Mechanical Engineering
Reference no: EM13719393

Galvanized iron drainpipes of diameter 50 mm are located at the four corners of a building, but three of them become clogged with debris. Find the rate of downpour (cm/min) at which a single functioning drainpipe can no longer drain the roof. The building roof area is 500 m2, and the height is 5 m. Assume the drainpipes are the same height as the building and that both ends are open to the atmosphere. Ignore minor losses.

Reference no: EM13719393

Questions Cloud

Find the expectation value of the potential energy : For the harmonic oscillator, find the expectation value of the potential energy for the lowest energy state
Assume that the density remains the same : Blue and yellow streams of paint (each with a density of 825 kg/m3 and a viscosity 1000 times greater than water) enter a pipe with an average velocity of 4 m/s as shown in the figure. The pipe has a diameter of 2 inches and length of 25ft. would you..
Determine the quality of the steam at the turbine exit : Consider a 210-MW steam power plant that operates on a simple non-ideal Rankine cycle, where the isentropic efficiency for both the turbine and the pump is 85%. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure ..
Describe the differences of the 2d solid element types : Identify a series of physical problems which lend themselves to being simplified to the use of a 2D solid element - Describe and discuss the differences of the 2D Solid Element types
Assume the drainpipes are the same height as the building : Galvanized iron drainpipes of diameter 50 mm are located at the four corners of a building, but three of them become clogged with debris. Find the rate of downpour (cm/min) at which a single functioning drainpipe can no longer drain the roof.
Rocket propellant chamber is filled with combustion gases : A 1m3 rocket propellant chamber is filled with combustion gases at 3000 K and 7 Mpa at the instant combustion ceases. The throat area of the nozzle is 0.1m2. Estimate the time it takes for the chamber pressure to drop to 0.7 MPa. Assume that the inst..
Converted to thermal energy due to the collision : Consider a mass M is a distance L above the ground at constant temperature, TR. The mass is released, falls, and hits the ground. The kinetic energy just before it hits is converted to thermal energy due to the collision and is transferred to the gro..
Determine the thermal efficiency and propulsion efficiency : A ramjet is to propel an aircraft at Mach 3 at high altitude where the ambient pressure is 8.5Kpa and the ambient temperature Ta is 220 k. The turbine inlet temperature T is 2540 k.if all components of the engine are ideal - that is frictionless.
An incompressible flow in cylindrical coordinates : An incompressible flow in cylindrical coordinates is given by:  Does this field satisfy continuity? For consistency, what should the dimensions of the constants K and b be?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd