User Account

All Pages

Assume the density of this metal at the given temperature

Assignment Help Mechanical Engineering
Reference no: EM13624653

The number of vacancies per cubic meter of a metal at 600°C is 3.1*1025 vacancies/m3. Assume the density of this metal at the given temperature is 5.84 g/cm3 and the atomic mass is 69.72g/mol. What is the required energy of vacancy of this metal?

Reference no: EM13624653

Questions Cloud

The treadmill display shows he has burned 620 kcal for jack : jack who weighs 150 lbf runs 5 miles in 43 minutes on a treadmill set at a one-degree incline. the treadmill display
A plane wall 15 cm thick has a thermal conductivity given : a plane wall 15 cm thick has a thermal conductivity given by the relation k 2.0 0.0005t wmk. where t is in kelvin.
If the average volume flow of blood through the aorta is 94 : if the average volume flow of blood through the aorta is 9.4 x 10-5 m3s and the cross-sectional area of the aorta is
A particular system obeys the relation uau-2expsr n moles : a particular system obeys the relation uau-2expsr n moles of this substance initially at temperature to and pressure po
Assume the density of this metal at the given temperature : the number of vacancies per cubic meter of a metal at 600degc is 3.11025 vacanciesm3. assume the density of this metal
Describe a scenario where you believe a binomial : describe a scenario where you believe a binomial distribution would be appropriate. describe a scenario where you
Two coupled identicle pendula of mass 3 kg are oscillating : two coupled identicle pendula of mass 3 kg are oscillating having started at rest with positions x10 0.22m and x20
For a newtonian fluid or a power law fluid flowing through : for a newtonian fluid or a power law fluid flowing through a cylindrical tube of radius r calculate the constant k in
Two blocks a and b are connected by a cord passing over two : two blocks a and b are connected by a cord passing over two pulleys c and d and e and f. at t 0 block a starts moving

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The motor is 15 in long and 10 in in diameter the a area is

a 1.5 hp motor is operarating in a room with air t of 20 c. the motor has an efficency of 78. the motor gives off heat

  What is the pressure differeence between the inside of a

what is the pressure differeence between the inside of a soap bubble and the atmosphere for a 3 inch diameter bubble?

  Explain working with boiler suspension bolts

Working with boiler suspension bolts. An HRT boiler is 4766mm long and 3533mm in diameter. It has 66 steel tubes with a diameter of 9mm. The total dry weight of the boiler is 2.565 tonnes

  Determine the entropy generated for carbon dioxide in a

determine the entropy generated for carbon dioxide in a pistoncylinder with an initial volume of 200 l at 300 degrees c

  A pipe flowing air at 1000 kpa 300 k is connected to the

a tank contains 1 m3 air at 100 kpa 300 k. a pipe flowing air at 1000 kpa 300 k is connected to the tank and it is

  Question 1approximate the torque and power necessary to

question 1approximate the torque and power necessary to rotate the inner 20 cm diameter cylinder shown in figure 1. sae

  Estimate the blood pressure in each branch

Estimate the blood pressure in each branch, assuming that blood vessels behave as rigid tubes, that we have frictionless flow, and that the vessel lies in the horizontal plane. What is the force generated at the branch by the blood? You may approx..

  What are the uses of wind tunnels including

this is concerned a little more into aerodynamics, what are the uses of wind tunnels including the importance of geometric and dynamic similarity and wind tunnel interference?

  Why we do not heat refregerated streams with a stream at a

why we need to avoid processes excessively large or excessively small thermodynamic driving forcesdifferences in

  A certain body is weighed at an elevation of 30000 ft where

a certain body is weighed at an elevation of 30000 ft where g32.08 ftsec2 by a spring balance that was calibrated at

  The bottom of the gate is 45 m below the water surface

a gate in the shape of a quarter cylinder hinged at a and sealed at b is 3 m wide. the bottom of the gate is 4.5 m

  Determine the minimum no of teeth required on pinion in

determine the minimum no of teeth required on pinion in order to avoid interference which is to gear with 1 a wheel to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd