Assume that the tests indicated that a tensile stress of

Assignment Help Mechanical Engineering
Reference no: EM13625437

An internal crack has been detected by means of X-rays in the shell of a large cylindrical pressure vessel. The stresses in the region of the crack area are a longitudinal tensile stress of sigma zz = 60000 psi, a circumferential tensile stress of sigma (theta theta) = 140000 psi, and a radial compressive stress of sigma rr = 5000 psi with sigma (r theta)= sigma rz = sigma (theta z)=0. The pressure vessel is so large tha there is no appreciable variation of stress over the region containing the crack. The crack is oriented so that its normal makes an angle of 40 degree with z- axis and 60 degree with y axis. what is the normal stress on the plane on the crack.

Laboratory test have shown that it is the tensile stress normal to the crack that causes it to propagte to failure. Assume that the tests indicated that a tensile stress of 120000 psi normal to the crack would cause a crack of the same size and shape to progagate. will the pressure vessel explode?

Reference no: EM13625437

Questions Cloud

What does a negative correlation statistic value : what does a negative correlation statistic value mean?a for most individuals both variables had values less than zerob
If the maximum and minimum pressures in the cycle are 6 mpa : a closed system contains 0.2 kg of air is used to execute a power carnot cycle between temperature limits of 315 k and
Determine the power required to maintain the clean rooms : at steady state a refrigeration cycle maintains a clean room at 55of by removing energy entering the room by heat
In a random sample of 5 parts on an assembly line the : 1. in a random sample of 5 parts on an assembly line the probability that one of the parts is defect is 15 and follows
Assume that the tests indicated that a tensile stress of : an internal crack has been detected by means of x-rays in the shell of a large cylindrical pressure vessel. the
A-the middle 997 of males scored between what two values : the average math sat score for males was 519 with a standard deviation of 105. for females avg math score was 484 with
It is desired to put oil hole through a part subjected to a : it is desired to put oil hole through a part subjected to a stress field given by sigma xx 15 ksi sigma yy -15 ksi
The beer institue conducted a study with looking at beer : the beer institue conducted a study with looking at beer purcheses per capita across states. some states buy more beer
Assuming that blood behaves as a newtonian fluid determine : a hollow-fiber dialysis unit is one design that provides a large surface area between blood and dialysate to permit

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd