User Account

All Pages

Assume that the efficiency of the jeeps power train is 20

Assignment Help Mechanical Engineering
Reference no: EM13611866

A car tows a 400kg block up a 45 degree incline. The coefficients of static and kinetic friction are 0.6 and 0.4. The car and the driver have a mass of 2000kg. Assuming that the wheels don't slip, what power must the ouput power of the car be to travel up the inlcine at 15m/s? Assume that the efficiency of the jeep's power train is 20%. What power input is required to achieve the required power output?

Reference no: EM13611866

Questions Cloud

The activation energy for creep is 140 kjmol calculate the : the steady-state creep rates at 473 k for any alloy are 2.510-3 h-1 at 55 mpa and 2.410-2 h-1 at 69 mpa. the activation
Andover corporation has been using the fifo cost flow : andover corporation has been using the fifo cost flow methodduring a prolonged period of inflation. during the same
What is the net force exerted by these two charges on a : two point charges are located on the x axis one charge q1 -17.5nc is located at x -1.740m the second charge q2
Flint tooling company is considering replacing a machine : flint tooling company is considering replacing a machine that has been used in its factory for two years. relevant data
Assume that the efficiency of the jeeps power train is 20 : a car tows a 400kg block up a 45 degree incline. the coefficients of static and kinetic friction are 0.6 and 0.4. the
A charge q1 31 times 10-6 c is placed at the origin charge : a charge q1 3.1 times 10-6 c is placed at the origin. charge q2 -6.8 times 10-6 c is placed on the x-axis at x -0.20
In step 1 net income before taxes was computed by multi : in step 1 net income before taxes was computed by multi plyingnet income of 33000000 by 100 and then dividing by 66000.
Soldner health care products inc expects to maintain the : soldner health care products inc. expects to maintain the same inventories at the end of 2010 as at the beginning of
Globals special order also requires 500 kilograms of : globals special order also requires 500 kilograms of genatope asolid chemical regularly used in the companys products.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the resultant internal loadings

the beam ab is pin supported at a and supported by a cable BC. determine the resultant internal loadings acting on the cross section at points d and e.

  If a rod of 1025 steel 05 m 197 in long is heated from 20

aif a rod of 1025 steel 0.5 m 19.7 in long is heated from 20 to 80 deg c 68 to 176 deg f while its ends are maintained

  Calculate the rate of flow

You are asked to measure the rate at which waste gases are being discharged from a stack. The gases entering contain 2.1 % carbon dioxide. Pure carbon dioxide is introduced into the bottom.

  Determine the resulting force created by the vehicle and

a construction vehicle of mass 30 mg is used to unload sand in a horizontal line through a port on the bottom of the

  Solid carbon reacts with steam to produce carbon monoxide

solid carbon reacts with steam to produce carbon monoxide and hydrogen. given an hc atom ratio of 11 and an oc atom

  Write down the continuity equation navier-stokes equations

a wire of radius ri is coated by a process described above. it is fed to a reservoir filled with a newtonian fluid with

  Lf the 50-kg crate starts from rest and achieves a velocity

lf the 50-kg crate starts from rest and achieves a velocity of v 4 ms when it travels a distance of 5 m to the right

  Determine the turbine inlet temperature

Determine the turbine inlet temperature, the cycle thermal efficiency, and the back-work ratio of this cycle.

  Determine the power of a pump if 2000 kgmin of water is

determine the power of a pump if 2000 kgmin of water is compressed from 100 kpa to 1 mpa. the water density can be

  Determine the change in internal energy kj and enthalpy kj

two kg of saturated liquid water at 1 bar is compressed to 25 bar and 100degc in a water pump. determine the change in

  If there is no change in potential energy and the speed

the work on a system with a mass 100 lbm is known to be 10 btus. if there is no change in potential energy and the

  Obtain the output response signal assuming a first order

a temperature measurement device with a time constant of 0.15 seconds outputs a voltage that is linearly proportional

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd