Asolute pressure is known at both inlet and outlet

Assignment Help Mechanical Engineering
Reference no: EM13612374

Water flows in a horizontal pipe with entrance velocity 2.5m/s is turning 90 degrees and leaves the pipe. Pipe diameter is d1=15cm at the entrance, then gradually decresases to d2=7.5cm. Absolute Pressure is known at both inlet and outlet , P1=168,600 Pa, P2=121,700 Pa. Calculate the force on the flange that mounts the horizontal section of the pipe.

Reference no: EM13612374

Questions Cloud

The chadmark corporations budgeted monthly sales are 3000 : the chadmark corporations budgeted monthly sales are 3000. in the first month 40 of its customers pay and take the 2
Velocity at the moment is v518 ms density p613 kgm3 assume : a spherical container with volume 0.05m3 is pressurized up to 800kpa absolute pressure. air is released suddenly
A company is producing two types of ski goggles thirty : a company is producing two types of ski goggles. thirty percent of the production is of type a and the rest is of type
A proton accelerates from rest in a uniform electric field : a proton accelerates from rest in a uniform electric field of 624 nc. at some later time its speed is 1.04 x 106 ms.a
Asolute pressure is known at both inlet and outlet : water flows in a horizontal pipe with entrance velocity 2.5ms is turning 90 degrees and leaves the pipe. pipe diameter
During the course we often discussed the concept of tax : during the course we often discussed the concept of tax doctrines. discuss where and how these originate and how they
You are a medical claims processor for humana claims arrive : you are a medical claims processor for humana. claims arrive at your desk at an average rate of three claims per day
Cconstant specific heats for air at room temperature : a turbojet aircraft is flying with a velocity of 320 ms at an altitude of 9150 m where the ambient conditions are 32
Sam works at the enrico arpaci mens clothing boutique in : sam works at the enrico arpaci mens clothing boutique in beverly hills earning 30000 per year. at work he wears enrico

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What delta p must be generated by the pump comment of the

a civil engineer is designing a pipe to transport 178 m3s of water a distance of 4.35 x 104 m. to save capital costs he

  Design problem - piston and flywheel

Design Problem - Piston and Flywheel : Analyze the motion of the crankshaft AB and flywheel for 0 ≤ θ ≤ 4Π (two complete rotations of the crankshaft, or all four cycles, beginning and ending at TDC), for different values of the four design paramete..

  What should the diameter of the nozzle outlet be

What should the diameter of the nozzle outlet be in inches and what is the mass flow rate of steam through the nozzle in lbm/min?

  Then use appropriate power equation to calculate the

a cylindrical bioreactor of diameter 3 m has four baffles. a marine impeller mounted in the reactor has a diameter 13

  Calculate the overall efficiency the heat rate mw and the

calculate the overall efficiency the heat rate mw and the total fuel rate kgs of a combined-cycle power plant 1 if no

  Determine a the pressure b the total internal energy and c

a 0.5-m3 vessel contains 10 kg of refrigerant-134a at -20oc. determine a the pressure b the total internal energy and c

  The following times to failure in hours were observed in an

the following times to failure in hours were observed in an experiment where 14 units were tested until eight of them

  Two particles a and b start from rest at the origin s 0

two particles a and b start from rest at the origin s 0 and move along a straight line such that aa 6t-3fts2 and ab

  A turbofan jet engine has a large fan that sucks in air

a turbofan jet engine has a large fan that sucks in air. some of this air enters a set of compressors is mixed with

  Heat transfer occurs until the volume on the inside of the

a piston-cylinder device contains 1 kg of h2o. the water is at 800oc and a pressure of 20 mpa. heat transfer occurs

  What is the percent span for the old and new set points

In order to increase production rate a reactor set point was increased from 160 psig to190 psig. The reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig.

  Find the maximum torque

Assuming a coefficient of static friction equal to 0.2 at the common surface, find the maximum torque that may be transmitted by the flywheel without slippage.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd