Angular velocity at instant

Assignment Help Mechanical Engineering
Reference no: EM13949021

1. The 10-lb bar is pinned at its center O and connected to a torsional spring. The spring has a stiffness k = 5 lb # ft>rad, so that the torque developed is M = (5u) lb # ft, where u is in radians. If the bar is released from rest when it is vertical at u = 90°, determine its angular velocity at the instant u = 0°.

2. The 10-lb bar is pinned at its center O and connected to a torsional spring. The spring has a stiffness k = 5 lb # ft>rad, so that the torque developed is M = (5u) lb # ft, where u is in radians. If the bar is released from rest when it is vertical at u = 90°, determine its angular velocity at the instant u = 45°.

Reference no: EM13949021

Questions Cloud

Discuss a story from an objective stance : Short Story "book" reports are informative reports that discuss a story from an objective stance. They are similar to reviews but half of the paper is a summary of the work and the other half is an evaluation of it. Short story "book" reports desc..
Net present value of this project given your sales forecasts : Your firm is considering a project with a five-year life and an initial cost of $130,000. The discount rate for the project is 12%. The firm expects to sell 2,100 units a year. The cash flow per unit is $20. What is the net present value of this proj..
Use an er diagram to represent the data modeling. : Sketch a course information table using the following table as an example. Feel free to add or remove attributes based on your analysis
Discounting-reinvestment and combination approach : The company uses a 9 percent interest rate on all of its projects. What is the MIRR of the project using the reinvestment approach? The discounting approach? The combination approach?
Angular velocity at instant : The 10-lb bar is pinned at its center O and connected to a torsional spring. The spring has a stiffness k = 5 lb # ft>rad, so that the torque developed is M = (5u) lb # ft, where u is in radians. If the bar is rele..
Discuss how ideas about how wellness and well-being have : Discuss how ideas about how wellness and well-being have developed as presented in the literature used in your module readings, as well as the modules themselves.Identify five concerns and discuss one concern that these issues raise in your mind, tha..
Calculate the annual incremental operating cash flows : Calculate the annual incremental operating cash flows for the new machine. Calculate the terminal value of the new machine.
Speculate on securities in order to help our company grow : To what extent do you agree or disagree with the following statement on a scale of 1 to 5 where 1 = strongly disagree and 5 = strongly agree. Please explain your answer. "As the Chief Financial Officer, I allocate 5% of our cash reserves each year to..
Public- and private-sector responders collaborate : What public- and private-sector resources could be used to respond to the threat? How can public- and private-sector responders collaborate?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What exactly is shaft power for a wind turbine what would

jon has decided to install a wind turbine at the top of the ridge. assume the wind velocity is hitting the turbine at a

  Gauge pressure and convert to absolute pressure

A pressure guage reads in tuscaloosa alababama 16 psi. can this pressure be a vacuumed pressure? Why or why not? if you think it can convert it to absolute pressure. If you think it cannot assume that it is a gauge pressure and convert to absolute pr..

  Magnitude of the support reaction on the left end of beam

A 20ft long beam has a support reaction at each end and a 12ft long uniformly distributed load of 20lb/ft starting on the left edge. The uniformly distributed load is modeled as a normal concentrated load of how many pounds?

  Determine the max shear developed on the web of this beam

a w16 x 50 steel beam supports a uniform load and a concentrated load. the distributed load is 1.5 kipft and

  Find pin dynamic forces and torque

Find: Pin dynamic forces and T (torque applied on link 2 ) to generate the required input velocity following requested output velocity of 25rpn Please note that for kinetic analysis

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  Define two infinite parallel plates are separated

Two infinite parallel plates are separated by a distance h. The space between them is filled with a Newtonian fluid: density (rho), viscosity (mu). The lower plate is fixed

  What is the maximum velocity that the car can achieve

a driver of a car is driving around in circles with a diameter of 100 ft. the driver is traveling 20 mpg when he

  Single crystal used to reinforce metal-matrix composites

An Al2O3 whisker is a small single crystal used to reinforce metal-matrix composites. Given a cylindrical shape, calculate the number of Al atoms and the number of O atoms in a whisker with a diameter of 1 micrometer and a length of 25 micrometers. (..

  What is the output power pout of motor at the instance that

the 50kg crate is hoisted up the 30 degree incline by the pulley system and motor m. crate started from rest and

  Find the work delivered by the turbine per unit mass of

superheated water vapor enters and insulated turbine operating at steady state at 20 bar and 400 degc and exits at 1.5

  Find a the work output of the heat engine b the efficiency

a carnot heat engine receives 90 kj from a reservoir at 627 . it rejects heat to the environment at 27 . one-fifth of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd