An oil pipeline was constructed to transport an oil with sg

Assignment Help Mechanical Engineering
Reference no: EM13629101

An oil pipeline was constructed to transport an oil with SG = 0.8 for a distance of 10 miles. The country was hilly, so the line made many ups and downs. These may be considered equivalent to 10 rises of 200 ft, followed by descents of 200 ft. When the pipe was completed it was tested by pumping water through it. The water flowed satisfactorily with an inlet pressure of 150 psi. Then the oil was slowly fed into the pipe. As the oil flowed, the pressure at the inlet end began to rise, and the flow rate began to fall. Finally, the flow stopped all together, while the pressure at the inlet side remained at 150 psi. Explain what caused this.

Reference no: EM13629101

Questions Cloud

Which of the following are true about vector components for : which of the following are true about vector components for vectors in two dimensions. choose all that apply they are
If you were constructing a 99 confidence interval of the : if you were constructing a 99 confidence interval of the population mean based on a sample of n25 where the standard
Determine the amount of heat transfer when this is done : in a close stationary system 2 kg of argon is heated from 20oc to 120oc. determine the amount of heat transfer when
Calculate the electric field at the center of a square 530 : calculate the electric field at the center of a square 53.0 cm on a side if one corner is occupied by a 48.0 microc
An oil pipeline was constructed to transport an oil with sg : an oil pipeline was constructed to transport an oil with sg 0.8 for a distance of 10 miles. the country was hilly so
What is the change of internal energy and enthalpy of 4 kg : what is the change of internal energy and enthalpy of 4 kg nitrogen as it changes from 50oc and 100kpa to 100oc and
A sewage plant produces 50000 gallons a day 20 of the time : a sewage plant produces 50000 gallons a day. 20 of the time it produces in excess of 60000 gallons what is the
A charge of 800 mc is placed at each corner of a square 120 : a charge of 8.00 mc is placed at each corner of a square 1.20 m on a side. determine the magnitude and direction of the
A tank contains 2500 m3 of salt solution with a salt : a tank contains 2500 m3 of salt solution with a salt concentration of 20 kgm3. at time zero salt free water starts to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the outside air temperature is -2 degc determine the

consider a house with inside air temperature of 22 degc. one of the walls of the house has three single-pane glass

  What is the net force exerted on a vertical 18c

what is the net force exerted on a vertical 18c rectangular plate that is 3m tall 5m wide and whose top edge is 2m

  Estimate time necessary to achieve the same concentration

Estimate the time necessary to achieve the same concentration at a 5.3-mm position for an identical steel and at the same carburizing temperature.

  Determine a the pressure b the total internal energy and c

a 0.5-m3 vessel contains 10 kg of refrigerant-134a at -20oc. determine a the pressure b the total internal energy and c

  The water at the constant pressure of 1 bar is

an electric water heater having 0.2 m3 capacity employs an electric heater to warm the water from 22degc to 55degc. the

  A stainless steel tube of 1 cm outer diameter and 1mm wall

a stainless steel tube of 1 cm outer diameter and 1mm wall thickness receives a uniform radiative heat flux of 100 wcm2

  Explain starting from the energy equation

Starting from the energy equation and using the one-dimensional heat conduction derivation as an example

  Noting that a person standing in a room maintained at

noting that a person standing in a room maintained at 20degc at all times the inner surfaces of the walls floors and

  Describe the principle and operation of an hearth furnace

Describe the principle and operation of an hearth furnace. Possible references: Making and Shaping of Steels by the American Society of Metals and Google resources.

  Determine the time required for the motion to stop what are

the wheel has a mass of 25 kg and a radius of gyration k0.15m. it is originally spinning at w140 rads. if it is placed

  What is the design objective

2. What is the design objective? -to minimize the required power input to the compressors 3. What parameters does the design engineer control?

  All four sides of the plate are maintained at 20 degree c

a 50-cm by 50-cm plate of pure nickel generates 3.9 mwm3 of energy uniformly within the plate. all four sides of the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd