An ice chest is constructed of styrofoam k 0033 wmc with

Assignment Help Mechanical Engineering
Reference no: EM13344032

An ice chest is constructed of Styrofoam (k = 0.033 W/m?C) with inside dimensions of 25 by 40 by 100 cm. The wall thickness is 5.0 cm. The outside of the chest is exposed to air at 25 ?C with h = 10 W/m2?C. If the chest is completely filled with ice, calculate the time for ice to completely melt. State your assumptions. The heat of fusion for water is 330 kJ/kg. 

Reference no: EM13344032

Questions Cloud

Calculate the heat required to raise the temperature of : the constant pressure molar heat capacity of a compound is found to vary with temperature.cpm 18.15 0.430t
You want to generate a sinusoidal signal which frequency : you want to generate a sinusoidal signal which frequency f varies continuously and parabolically from 500 hz to 3500
The isomerization of cyclopropane to form propenenbsp is a : the isomerization of cyclopropane to form propenenbsp is a first-order reaction. at 760 k 85 of a sample of
Consider a cup of coffee that has a temperature of 93oc : consider a cup of coffee that has a temperature of 93oc. assume the mass of the coffee is 550 g and that the specific
An ice chest is constructed of styrofoam k 0033 wmc with : an ice chest is constructed of styrofoam k 0.033 wm?c with inside dimensions of 25 by 40 by 100 cm. the wall thickness
Rewrite the following code using only continuous : rewrite the following code using only continuous assignment statements. module behavmoduleinput a b c d e output reg
A 50 g sample of hemoglobin requires 216 ml of 000310 m : the iron content of hemoglobin can be determined by converting the iron to fe2 and titrating using mno4-. a 5.0 g
The volume of 4 cubic meters of gas is kept under constant : the volume of 4 cubic meters of gas is kept under constant pressure. its tempeture is increased from a minus 73 degrees
A steam power plant operates on an ideal : a steam power plant operates on an ideal reheat-regenerative rankine cycle and has a netnbsppower output of 80 mw.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the thermal efficiency and the mean effective

If the maximum temperature in the cycle is not to exceed 2200 K, determine the thermal efficiency and the mean effective pressure.

  What is the activitys slope

Given that an activity's normal time and cost are 10 days and $400 and its crash time and cost are 5 days and $800, what is the activity's slope?

  Determine the magnitudes of fa and fb

The total force Fa + Fb exerted on the shelter is in the direction parallel to the line L and it's magnitude is 400 lb. Graphically determine the magnitudes of Fa and Fb.

  The corresponding magnitude of r

Two control rods are attached at A to lever AB. Using trigonometry and knowing that force in the right-hand rod is F2=20 lb, determine a.) the required force F1 in the left-hand rod if the resultant R of the forces exerted by the rods on the le..

  What is the bullet maximum velocity

Assuming this pressure creates a force of F = F 0sin( t / t0) on the bullet, determine the velocity of the bullet at any instant it is in the barrel. What is the bullet"s maximum velocity?

  Determine the overall efficiency of the pump-motor unit

water is pump from a lake to a storage tank at 18m above at a rate of 70 L/s while consuming 20.4 kW of electric power. disregarding any frictional losses in the pipes and any change s in kinetic energy, determine (a) the overall efficiency of the..

  Calculate the time for the ice to completely melt

If the chest is completely filled with ice, calculate the time for the ice to completely melt. State your assumptions. The enthalpy of fusion for water is 330 kJ/kg.

  Problem 1 the u-tube manometer shown below is open to the

problem 1 the u-tube manometer shown below is open to the atmosphere and partiallynbspfilled with water so that the

  Find the air exit temperature from the compressor

Air exits from the nozzle at 800m/s. find the air exit temperature from the compressor.

  Module fea - finite element analysis

Module FEA - FINITE ELEMENT ANALYSIS ,  Provide answers to all questions. Note that assignment part 2 carries 60% of the marks for the course.

  Determine the power of the pump

Determine the power of the pump. The efficiency of the pump is 65%.

  What is a capacitor

but they vary in number of outputs, interfacing, cascadability, current limiting, and drive capability. As always, examine the data sheets carefully before substituting these parts! What is a Capacitor?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd