User Account

All Pages

An enclosure box surrounds some electronics that draw 25 w

Assignment Help Mechanical Engineering
Reference no: EM13626698

An enclosure box surrounds some electronics that draw 25 W of electrical power. For heat transfer we will just consider the biggest wall and ignore other sides, in this case. The wall is a 0.8 mm thick aluminum (kAL = 200 W/m-C), and 200 cm length x 100 cm width. The outside air is at 20 C and the convection coefficient outside, houtside = 200 W/m2-C due to a fan running. For the inside, hinside = 5 W/m2-C. How hot will the inside air get under these conditions?

Reference no: EM13626698

Questions Cloud

What is the probability that you come out even of win money : you are in possession of an unusual 5-sided die. specifically the die which is not evenly weighted takes on five
One cube has sides of length l100 cm the electric field is : one cube has sides of length l10.0 cm. the electric field is uniform has magnitude e 4.00x103nc and is parallel to the
If the carbon dioxide behaves as an ideal gas determine the : five kg of carbon dioxide gas undergoes a process in a well insulated piston-cylinder assembly from 2 bar 280k to 20
Also please show steps using excel or by hand on how to : are americans more deeply in debt this year compared to last year? to help answer this question a statistics
An enclosure box surrounds some electronics that draw 25 w : an enclosure box surrounds some electronics that draw 25 w of electrical power. for heat transfer we will just consider
A building wall is made of 200 mm of poured concrete on the : a building wall is made of 200 mm of poured concrete on the outside 100 mm of fiberglass insulation in the middle and
A solenoid with n1800 turnsm and a current i1 3a is filled : a solenoid with n1800 turnsm and a current i1 3a is filled with a paragmagnetic material at t1 250 k. a second
The quality control manager at a light bulb factory needs : the quality control manager at a light bulb factory needs to estimate the mean life of a large shipment of light bulbs.
An electric-powered water pump must fill up a 50000 gallon : an electric-powered water pump must fill up a 50000 gallon elevated water tank in which the water averages 60 feet

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The mean diameter of a conical friction clutch

The mean diameter of a conical friction clutch is 250mm with a width of the conical surface being 50mm. The clutch is lined with a material having a coefficient of friction of 0.25

  In an accelerator protons emerge with velocity of 25 x 108

in an accelerator protons emerge with velocity of 2.5 x 108 ms. the accelerator is 0.8km long.a if the acceleration is

  Vital information about pressure cooker

Important information about Pressure Cooker, Steam is leaving a pressure cooker whose operating pressure is 30 psi. It is observed that the amount of liquid in the cooker has decreased by 0.4 gal in 45 minutes after the steady operating conditions..

  The shaft runs in a bearing whose length is 15 times the

a 150mm diameter shaft supporting a load of 10kn has a speed of 1500rpm. the shaft runs in a bearing whose length is

  Test the hypothesis that the two process have identical

two processes are used to produce forgings used in an aircraft wing assembly. of 200 forgings selected from process 1

  Pressures change from 325 k and 125 kpa to 500 k and 300

during actual expansion and compression processes of gases pressure and volume are often related by pvn c where n and

  As the hollow steel g 77 gpa shaft shown rotates at 180

as the hollow steel g 77 gpa shaft shown rotates at 180 rpm a stroboscopic measurement indicates that the angle of

  The whole system is now heated until the volume of chamber

in this piston-cylinder device d1 20 cm-diameter d2 10 cm-diameter and the initial volume of chamber 2 is 0.1 m3.

  The 8 kg sack slides down the smooth ramp if it has a

the 8 kg sack slides down the smooth ramp. if it has a speed of 1.5ms when y.2m. determine the normal reaction the ramp

  The inital parameters of the air in the cylinder were 10 l

air was heated by an electric resitance heater in an insulated piston-cylinder device. the piston weight remained

  Heat is now transferred to the refrigerant at constant

a mass of 0.2 kg of saturated refrigerant-134a is contained in a piston-cylinder device at 200 kpa. initially 75 of the

  As the load on the motor is increased the developed torque

a 115-v shunt motor develops 21 ib-ft when the armature current is 12 a. as the load on the motor is increased the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd