An elevated open stairway like the one in the sac is

Assignment Help Mechanical Engineering
Reference no: EM13627043

An elevated open stairway (like the one in the SAC!) is designed to be supported by four steel rods connecting the stairway to the ceiling. The weight of the stairway plus a full load of people is 9577 pounds. If the rods are 0.9 inches in diameter and the allowable stress of the steel used is 80,000 psi, what is the safety factor of this design?

Reference no: EM13627043

Previous Q& A

  Assume that a sample is used to estimate a population

assume that a sample is used to estimate a population proportion p. find the margin of error e that corresponds to the

  Ten kilograms of ice at 260 k is duped into 20 kg of

ten kilograms of ice at 260 k is duped into 20 kg of liquid water initially at 300 k in an insulated container. the

  A power drive shaft is designed with a safety factor of 8

a power drive shaft is designed with a safety factor of 8. the shaft is subjected only to torsional load torque. if the

  Students want to construct a scattering experiment using a

students want to construct a scattering experiment using a power source of 5.5 mev alpha-particles to scatter from a

  A boring bar 1 inch in diameter extends 2 inches from the

a boring bar 1 inch in diameter extends 2 inches from the tool post. when the bar is subjected to a machining force

  You are a blackbody with a temperature 986 degrees f a what

you are a blackbody with a temperature 98.6 degrees f.a what is the total energy density of the radiation you emit?b

  After a star like the sun stops producing energy via fusion

after a star like the sun stops producing energy via fusion it collapses into a degenerate object called a white dwarf

  What is the probability that the first card is a queen and

suppose that two cards are randomly selected from a standard 52-card deck.a what is the probability that the first card

  A vessel contains 4 kg of wet steam liquid-vapor mixture at

a vessel contains 4 kg of wet steam liquid-vapor mixture at 140 degc. after the addition of heat the steam has a

  It is important for nuclear engineers to know the thermal

it is important for nuclear engineers to know the thermal properties of neutrons in a nuclear reactor. assuming a gas

Reviews

Write a Review

 

Similar Q& A

  How long will it be before the exiting water reaches 38c

a residential hot water heater initially contains water at 60c degree celcius someone turns on a shower and draws water

  A 600 mw coal-fired power plant has an overall thermal

a 600 mw coal-fired power plant has an overall thermal efficiency of 38. it is burning coal that has a heating value of

  Two blocks of steel cp011 btulbm ordmf one at 800ordmf and

two blocks of steel cp0.11 btulbm ordmf one at 800ordmf and the other at 300ordmf are brought into contact in an

  Determine the power required for a 1150-kg car to climb a

determine the power required for a 1150-kg car to climb a 100-m-long up hill road with a slope of 30degrees from

  Determine the range of te distance d

the maximum allowable value of each of the reactions is 180 N neglecting of the weight of beam, determine the range of te distance d for which the beam is safe.

  Estimate the theoretical fracture strength

Estimate the theoretical fracture strength of a brittle material if it is known that fracture occurs by the propagation of an elliptically shaped surface crack of length 0.16 mm and that has a tip radius of curvature of 0.002 mm when a stress of 1..

  Calculate the battery failure probability under normal

a particulate monitor has a power supply consisting of two batteries in parallel. either battery is adequate to

  The frictional driving force acting on the wheels of the

for a short period of time the frictional driving force acting on the wheels of the 2.4-mg van is fd 600t2 n where t

  There are a reservoir at point zero and another one 80

there are a reservoir at point zero and another one 80 meter higher. they are 1km from eachother. the upper reservoir

  At the beginning of compression p1 85 kpa and t1 305 k

an air-standard otto cycle has a compression ratio of 7.5. at the beginning of compression p1 85 kpa and t1 305 k.

  A refrigerator operates on the ideal vapor compression

a refrigerator operates on the ideal vapor compression refrigeration cycle with r-134a as the working fluid between the

  Find the orthogonal rake angle of the cutting tool

the friction force acting at the chip-tool interface the main (tengential ) cutting force is 1500N . Find the orthogonal rake angle of the cutting tool?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd