User Account

All Pages

Airborne contaminant hazards explain

Assignment Help Mechanical Engineering
Reference no: EM13699718

1.Discuss whether you think OSHA's air contaminant standards are important, and why. Do you think they are adequate to protect employees in the workplace from airborne contaminant hazards? Explain.

2.Compare and contrast the training requirements in the Hazard Communication Standard (HAZCOM) (1910.1200) and the Lead Standard (1910.1025). If an employee is exposed to lead above the action level, would the training specified in the HAZCOM standard be adequate? Why, or why not?

Each question 200 words or more using APA format with one reference cited for each question.

Reference no: EM13699718

Questions Cloud

What would the canoe speed in a still lake : Two students are canoeing on a river. While heading upstream, they accidentally drop an empty bottle overboard. What would the canoe speed in a still lake be for the same paddling effort
Find the direction of the wind velocity : An airplane pilot sets a compass course due west and maintains an airspeed of 217km/h. Find the direction of the wind velocity
Where does it strike relative to its starting point : Two horizontal metal plates, each 100 mm square, are aligned 10.0mm apart, with one above the other. Where does it strike, relative to its starting point
What is the speed of the plane over the ground : An airplane pilot wishes to fly due west. A wind of 74.0km/h is blowing toward the south. What is the speed of the plane over the ground
Airborne contaminant hazards explain : 1.Discuss whether you think OSHA's air contaminant standards are important, and why. Do you think they are adequate to protect employees in the workplace from airborne contaminant hazards? Explain.
How far from the central bright spot : In a double-slit experiment, the third-order maximum for light of wavelength 500nm is located 12mm from the central bright spot on a screen 1.5m from the slits. How far from the central bright spot will the second-order maximum of this light be loc..
Calculate h2asc, hasc^- : Problem- Ascorbic acid (H2C6H6O6 or HAsc), known as vitamin c, is a diprotic acid (Kal= 1.0 x 10 ^-5 and Ka2= 5 x 10 ^-12) found in cirus fruit. Calculate [H2Asc], [HAsc^-], [Asc^2-], and the pH of 0.050M H2Asc. Please break down the steps so I kn..
What is the total distance her car travels : An Automobile is traveling on a long, straight highway at a steady 76.0 mi/h when the driver sees a wreck 180m ahead. What is the total distance her car travels before it comes to a stop
Determine the horizontal distance traveled by the bullet : A bullet is fired from a rifle that is held at 1.6m above the ground in a horizontal position. The initial speed of the bullet is 600 m/s. Determine the horizontal distance traveled by the bullet

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Solar energy reaching the earth is about 1350 wm2 outside

solar energy reaching the earth is about 1350 wm2 outside the earths atmosphere and 950 wm2 on earths surface normal to

  Steam enters a two-stage adiabatic turbine at 8 mpa and

steam enters a two-stage adiabatic turbine at 8 mpa and 550ordmc state 1 and is expanded to 2 mpa state 2 in the first

  The mark for water has risen 06 cm above the liquid-air

the density of a liquid is to be determined by an old 1cm diameter cylindrical hydrometer whose division marks are

  The experiment is repeated with a metallic sphere of the

a small sphere of reference-grade iron with a specific heat of 447 jkgk and a mass of 0.515 kg is suddenly immersed in

  Find the magnitdue of the acceleration when it reaches

a sled is traveling down a curve which can be approxmiated by a parabola y .01x2. find the magnitdue of the

  Determine the largest couple moment m

The uniform 6-kg slender rod rests on the top center of the 3kg block. If the coefficients of static friction at the points of contact are ua=.4 and ub=.6, and uc=.3, determine the largest couple moment M which can be applied to the rod without ca..

  Wet steam p128 kpa x090 enters a heat exchanger with a

wet steam p12.8 kpa x0.90 enters a heat exchanger with a flow rate of 1.2 kgs. cold water at 12.8 kpa and k also

  Air modeled as an ideal gas enters a steady state adiabatic

air modeled as an ideal gas enters a steady state adiabatic turbine at 1200 k and exits at 100 kpa 700 k. the

  For this case assume that the pressure losses in the

design a single stage rocket for mars orbital insertion liftoff from mars. required deltavee3.5 kmsec using

  A variable force and appropriate energy transfers are

ten kilograms of water initially at 3000 kpa 200degc are contained in a piston-cylindernbspdevice shown below. a

  Analysis using ansys fea is required linear structural

analysis using ansys fea is required. linear structural vibrationmodal and steady state thermal analysis can be use to

  Calculate the change in specific internal energy and

calculate the change in specific internal energy and enthalpy of air for a process starting at 250 k and ending at 500

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd