Air flows in a channel whose velocity at 3 neighbouring

Assignment Help Mechanical Engineering
Reference no: EM13343947

Air flows in a channel whose velocity at 3 neighbouring points a,b, and c, which are 10 cm apart, are shown in the following figure. find the density graident at point b if the fluid temperature is 40 degrees c and the absolute static pressure is 360kpa.

Reference no: EM13343947

Questions Cloud

The manometer shown above in problem 1 above contains water : the manometer shown above in problem 1 above contains water and kerosene. with both tubes open to the atmosphere the
What volume of 0131 m bacl2 is required to react completely : what volume of 0.131 m bacl2 is required to react completely with 42.0 ml of 0.453 m na2so4? the net ionic equation for
An experiment shows that a 247ml gas sample has a mass of : an experiment shows that a 247ml gas sample has a mass of 0.432 gas at a pressure of 752 mmhg and a temperature of 28c.
A compound contains only carbon hydrogen and oxygen : a compound contains only carbon hydrogen and oxygen. combustion of 0.01068 g of the compound yields 0.01601 g of co2
Air flows in a channel whose velocity at 3 neighbouring : air flows in a channel whose velocity at 3 neighbouring points ab and c which are 10 cm apart are shown in the
An unknown sample of cu2 gave an absorbance of 0262 in aa : an unknown sample of cu2 gave an absorbance of 0.262 in aa analysis. then 1.00 ml of solution containing 100.0 ppm cu2
Explain the following terms with respect to 4-storke cycle : explain the following terms with respect to 4-storke cycle internal combustion engines strokebore ratio piston
Calculate the pressure in atm exerted by 100 mole of : calculate the pressure in atm exerted by 1.00 mole of acetylene at 125degc in a 20.0-liter container. the van der waals
If a student determined that the circumference of a : if a student determined that the circumference of a balloon filled by the boiling point of liquid nitrogen was 45 cm

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the cooling water flow rate

Determine the flow rate of steam from the boiler in lb/h

  Find max specific range and max range airspeed

Find Max Level Airspeed at 95% RPM and find Max Range Airspeed (VBR) and Max Endurance Airspeed (VBE) - find Max Specific Range and Max Range Airspeed

  Determine the components of force reaction

The link lies in a plane parallel to the y-z plane and the bearings are properly aligned on the shaft.

  Determine the temperature of the electric heater element

Determine the temperature of the electric heater element and drawing of the temperature profile.

  Estimate the torque required at the base of a flag pole

Estimate the torque required at the base of a flag pole to hold it in place in a 30mph wind. Assume the flag pole is a vertical cylinder with D=10cm and L=10m, and assume the wind drag force is uniform along the pole.

  Determine the moment of p about a

a 13.2-N force P is applied to the lever which controls the auger of a snowblower. Determine the moment of P about A when alpha is equal to 30 degrees.

  Calculate the initial angular acceleration

A dump truck is shown in the figure. The loaded container has a mass of 8000 Kg and may be modelled as a solid homogeneous block. The hydraulic cylinder applies a force of 300 kN to the container in the starting position shown.

  Determine the radius of curvature of the path of the package

package is dropped from the plane which is flying with a constant horizontal velocity of vA = 150 ft/s at a height h = 1500 ft. Determine the radius of curvature of the path of the package just after it is released from plane at A.

  Approximate location of the laminar turbulent transition

Find the approximate location of the laminar turbulent transition - what is the net heat removed by the air around the rod?

  What is the ideal mechanical advantage of the system

A wheel barrow is used to lift a 200 lb load. The length from the wheel axle to the center of the load is 2 ft. The length from the wheel and axle to the effort is 5 ft. 5. What is the ideal mechanical advantage of the system?

  Determine the temperature at which the liquid

A rigid tank with a volum of 2.5m^3 contains 5kg of saturated liquid-vapor mixture of water at 75deg C. Now the water is slowly heated. Determine the temperature at which the liquid in the tank is completely vaporized

  What is velocity and acceleration of ball at tube

canon at an angle 30 degree tube is rotating at an axes with anguar velocities w1 and w2 2 and 5 rad/s and tube blows a ball at b with constant rate 7 m/s . what is velocity and acceleration of ball at tube end ball is at distance of 3m from tube ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd