User Account

All Pages

Air enters and air compressor at a steady volume flow rate

Assignment Help Mechanical Engineering
Reference no: EM13628899

Air enters and air compressor at a steady volume flow rate of 45 m^3/min. The air pressure increases from 100 to 700 KPa while heat is removed from the air at a rate of 20kW. The air temperature at the inlet to the compressor is 25 degrees Celsius, and the exit temperature is 150 degrees Celsius. The air leaves the compressor through a pipe with an area of 0.03 m^2. Determine the power necessary to operate the compressor under these conditions.

Reference no: EM13628899

Questions Cloud

Two site are being considered for wind power generation in : two site are being considered for wind power generation. in the first site the wind blows steadily at 7 ms for 3000
The exit temperature of the water is 25oc then what is the : an adiabatic heat exchanger has 0.3 kgs of water passing through one flow path. the inlet temperature and pressure are
Dry air enters an industrial dryer with a pressure of 101 : dry air enters an industrial dryer with a pressure of 101 kpa a temperature of 250c and a mass flow rate of 2.6kghr
A engineer is going to redesign an ejection seat for an : a engineer is going to redesign an ejection seat for an airplane. the seat was designed for pilots weighing between 120
Air enters and air compressor at a steady volume flow rate : air enters and air compressor at a steady volume flow rate of 45 m3min. the air pressure increases from 100 to 700 kpa
A psychologist would like to evaluate the relationship : a psychologist would like to evaluate the relationship between academic ability as measured by the act and academic
A closed system consisting of 145 lb of air undergoes a : a closed system consisting of 14.5 lb of air undergoes a polytropic process from p1 80 lbfin2 v1 4 ft3lb to a final
Assume that womens heights are normally distributed with a : assume that womens heights are normally distributed with a mean given by u62.3in and a standard deviation given by
The liquid water stream enters at 60 psia and 60f then : a mixing chamber combines superheated steam and liquid water to produce a stream of saturated steam with a quality of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Heat is generated in a 14-m-long 02-cm-diameter electrical

heat is generated in a 1.4-m-long 0.2-cm-diameter electrical wire that extends across a room which is maintained at

  Determine the work produce

Refrigerant 134a at 700 kPa and 40oC is expanded adiabatically in a closed system to 60 kPa. Determine the work produced, in kJ/kg, and final enthalpy for an isentropic expansion efficiency of 80.

  A steam power plant operates on an ideal regenerative

a steam power plant operates on an ideal regenerative rankine cycle with two open feedwater heaters. steam enters the

  Estimate as closely as possible the entropy change of the

consider a cylinder containing 4 moles of compressed argon to 10 bar and 298 k. the cylinder is housed in a big lab

  A cylindrical duct supplies 120 kgs of combustion air at

a cylindrical duct supplies 1.20 kgs of combustion air at 150 c and 95.0 kpa to a furnace. if the velocity of the air

  If a batch formula for 2130 kg of window glass consists of

if a batch formula for 2130 kg of window glass consists of 500 kg of caco3 1150 kg sio2and an unknown amount of na2co3.

  Drmine a the temperature of the air at the compressor

the turbocharger of an internal combustion engine consists of a turbine and a compressor. hot exhaust gases flow

  A spherical balloon contains 2 kg of water at 230 degrees c

a spherical balloon contains 2 kg of water at 230 degrees c 400 kpa the specific volume is 0.5951 m3kg. the balloon

  Briefly explain the difference between fatigue striations

Briefly explain the difference between fatigue striations and beachmarks in terms of both size and origin.

  What magnetic field should be applied to trap electrons

In a DC planar magnetron sputtering system at 1000 V, the cathodeanode spacing is 10 cm. What magnetic field should be applied to trap electrons within 0.5 cm of the target?

  At a point on the free surface of a machine part the

at a point on the free surface of a machine part the strains are ex1200 mu ey300mu yxy700 mu. use mohrs circle to

  For an undamped sdof spring mass system m5kg and k2000 nm

for an undamped sdof spring mass system m5kg and k2000 nm. plot the displacement and acceleration of the system using

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd