Air at 7 kpa and 35 degc flows over a flat plate at 75 ms

Assignment Help Mechanical Engineering
Reference no: EM13628254

Air at 7 kPa and 35 °C flows over a flat plate at 7.5 m/s. The plate is 30 cm square and is maintained at 65 °C.

a. Determine if the air flow is laminar or turbulent. Justify your answer.

b. Estimate the heat lost from the plate in W.

Reference no: EM13628254

Questions Cloud

A rocket is launched and attains a spped of 7900 ms when : a rocket is launched and attains a spped of 7900 ms when 35000 m abovve the surface of the earth. if the engines then
Which of the following would cause a change in a feasible : which of the following would cause a change in a feasible region?removing a redundant constraintincreasing an objective
Determine the magnitude and coordinate direction angles of : if f1 110n f2 121n and f3 85n determine the magnitude and coordinate direction angles of the resultant couple
Calculate the convective heat transfer coefficient : air at a pressure of 200 kpa and free stream temperature of 27 degc flows over a square plate at a velocity of 30 ms.
Air at 7 kpa and 35 degc flows over a flat plate at 75 ms : air at 7 kpa and 35 degc flows over a flat plate at 7.5 ms. the plate is 30 cm square and is maintained at 65 degc.a.
A researcher testing the effects of two treatments for : a researcher testing the effects of two treatments for anxiety computed a 95 confidence interval for the difference
Catapult fires an 800-kg rock with an initial velocity of : catapult fires an 800-kg rock with an initial velocity of 100 msat a 40deg angle from ground. what is the magnitude of
Determine the mole fractions of polyvinyl chloride and : determine the mole fractions of polyvinyl chloride and polyvinyl acetate in a copolymer having a molecular weight of
A skater is spinning with his arms outstretched he has a : a skater is spinning with his arms outstretched. he has a 2-lb weight in each hand. in an attempt to change his angular

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What values of the initial angle will cause the ball to

the basketball player likes to release his foul shots with an initial speed v0 23.5ftsec. what values of the initial

  What maximum load can the member take before buckling would

a round compression member with both ends pinned and made of aisi cold-drawn steel sy441 mpa e207 gpa is to be used in

  Find i the maximum pressure shown by a gauge on the cooker

2 kg of water at 10oc and atmospheric pressure are placed in a pressure cooker and heated until the water boils at

  Determine the rate of entropy generation of the steam

steam enters an adiabatic turbine at 8 mpa and 520 degc with a volumetric flow rate of 0.8 m3s and exits at 30 kpa. the

  The inner diameter of the hose is 1 inch and it reduces to

a garden hose attached with a nozzle is used to fill a 20-gal bucket. the inner diameter of the hose is 1 inch and it

  Consider no change in heat transfer kinetic and potential

consider a steam turbine in which the steam enters at 23.26 mpa and 808 k with a flow rate of 17.78 kgs. the steam

  Determine the final mass at the end

The velocity at the inlet is controlled so that it changes according to the following expression. V=a-ct^2, where a = 20m/s, c- 0.8m/s. If the tank initially contains 3kg of liquid water, determine the final mass at the end if 4 seconds of flow.

  A piston cylinder device contains 1 kg water at 20oc with a

a piston cylinder device contains 1 kg water at 20oc with a volume of 0.01 m3 by mistake someone locks the piston

  A motorist enters a freeway at 36 kph and accelerates

a motorist enters a freeway at 36 kph and accelerates uniformly to 90 kph. from the odometer in the car the motorist

  Using the components system shown provide an expression for

an airplane a takes off as shown with a constant speed equal to v110kmh. the path of the airplane is described in the

  Kinetic and potential energy changes are negligible what is

at steady state a device receives a stream of saturated water vapor at 210 degrees c and discharges a condensate stream

  Calculate the transverse modulus of the peek

calculate the transverse modulus of the peek/carbon fiber composite with 30% volume fraction by tow method. the modulus of peek is 3.8 GPa and the modulus of the carbon fiber is 400GPa. assume the reinforcing factor.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd