Air at 2900 r 435 psia enters a turbine operating at steady

Assignment Help Mechanical Engineering
Reference no: EM13612979

Air at 2900 R, 435 psia enters a turbine operating at steady state and expands adiabatically to the exit, where the temperature is 1500 R. If the isentropic turbine efficiency is 90%, determine

(a) the pressure at the exit (psia),

b) the work developed, in Btu per lbm of air flowing.

Assume ideal gas behavior for the air and ignore kinetic and potential energy effects.

Reference no: EM13612979

Questions Cloud

It supplies heat to a room at a rate of 46000 btuhr in : a heat pump has a second law efficiency of of 74. it supplies heat to a room at a rate of 46000 btuhr in order to
A die is rolled 24 independent times let y be the sum of : 1. let x equal the number of alpha particles counted by a geiger counter during 30 seconds. assume that the
Two small spheres spaced 500 centimeters apart have equal : two small spheres spaced 50.0 centimeters apart have equal charge. how many excess electrons must be present on each
The estimate of the slope is the estimate of the : the managers of a brokerage firm are interested in finding out if the number of new clients a broker brings into the
Air at 2900 r 435 psia enters a turbine operating at steady : air at 2900 r 435 psia enters a turbine operating at steady state and expands adiabatically to the exit where the
An elevator and its load have a combined mass of 1450 kg : an elevator and its load have a combined mass of 1450 kg. find the tension in the supporting cable when the elevator
A police car is traveling east at 400 ms along a straight : a police car is traveling east at 40.0 ms along a straight road overtaking a car ahead of it moving east at 30.0 ms.
Obtain a point estimate of the mean number of rolls of a : what is the mean number of rolls of a die before a 1 is observed?1- obtain a point estimate of the mean number of rolls
Calculate thermal efficiency of the power plant show the : a gas power cycle compresses air at 1 bar and 300 k state 1 through an adiabatic reversible compressor to 6 bar state

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Knowing that the fairway slopes downward at an average

a golfer hits a golf ball with an initial velocity of 160 fts at an angle of 25deg with the horizontal. knowing that

  Determine the magnitudes of fa and fb

The total force Fa + Fb exerted on the shelter is in the direction parallel to the line L and it's magnitude is 400 lb. Graphically determine the magnitudes of Fa and Fb.

  Its specific heat ratio is 14 and gas constant is 0287

an open brayton cycle engine operates with a compressor-pressure ratio of 6 an inlet temperature of 20 c and inlet

  If the basement is heated by a gas furnace operating at an

the concrete slab of the basement is 11 m long 8 m wide and 0.20 m thick. during the winter temperatures are nominally

  Describe the fracture behaviour of the insulation tape

Cracks propagate when the stress intensity factor exceeds a critical value and describe the fracture behaviour of the insulation tape loaded with a small crack.

  Calculate the temperature of the gas in the tank

comment on any safety hazards that might be encountered. especially, what would you anticipate if the inlet gas control valve were to malfunction and the gas space above the fuel were to reach full storage tank pressure (69bar)? the fuel tank has ..

  Calculate the normal stress positive if tensile and

a cylindrical bronze sleeve 2 is held in compression against a rigid machine wall by a high-strength steel bolt 1 as

  Determine the work and heat transfer

determine the work and heat transfer, each in kJ. sketch the process on p-v and T-s coordinates. Associate the work and heat transfer with areas on these diagrams.

  What are the forces acting on workpiece

What are the forces acting on workpiece during turning process. how workpiece should be clamp

  Calculate the final plume rise in a neutral atmosphere

for a wind speed of 6 ms a stack gas exit velocity of 20 ms a stack diameter of 4 m a heat emission rate of 15 mw and

  What is the potential temperature profile at the end

plot the evolution of the height, h, of the stable boundary layer and the strength, delta thetas, as a function of time.

  Calculate the crack length

Calculate the crack length after cycles and subjected to a cyclic stress normal to the crack

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd