Air at 147 psia and 60 degf enters a heavy duty compressor

Assignment Help Mechanical Engineering
Reference no: EM13626232

Air at 14.7 psia and 60 °F enters a heavy duty compressor with negligibly small inlet speed. The air is discharge at a rate of 20 lbm/sec at 90 psia, and with a speed of 500 ft/s. If the power input is 3200 hp and the rate of heat transfer from the compressor is controlled by a cooling system to be 11 Btu/hr, determine the temperature of the discharged air. Considering the rise in internal energy, determine the efficiency of the compressor, Nc.

Reference no: EM13626232

Questions Cloud

Light is incident of the surface of metallic sodium whose : light is incident of the surface of metallic sodium whose work function is 2.3 ev. the maximum speed of the
Suppose a survey participant is randomly selected and you : drake marketing and promotions has randomly surveyed 200 men who watch professional sports. the men were separated
Crate slides down the section of the spiral ramp such that : crate slides down the section of the spiral ramp such that r .5zft and z 100 - .1t2ft where t is in seconds. if the
A particle lives for a short time before breaking apart : a particle lives for a short time before breaking apart into otherparticles. suppose it is moving at a speed of 0.972c
Air at 147 psia and 60 degf enters a heavy duty compressor : air at 14.7 psia and 60 degf enters a heavy duty compressor with negligibly small inlet speed. the air is discharge at
A uniform rectangular plate is hanging vertically downward : a uniform rectangular plate is hanging vertically downward from a hinge that passes along its left edge. by blowing air
Find the flowrate in million standard cubic feet per day : natural gas is flowing in a 20 inch sch 40 carbon steel pipeline that is 300 miles long. there is a gas compressor at
Information about a regression analysis includes an : information about a regression analysis includes an intercept of 5.99 and a slope of 0. make a prediction of y based on
Assume that the speed of the water in the reservoir is zero : a hand-pumped water gun is held level at a height of 0.53 m above the ground and fired. the water stream from the gun

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assume the roughness wavelength is 10m and its amplitude is

a car and its suspension system are idealized as a damped spring-mass system with natural frequency 0.5hz and damping

  Product and engineering design review

Product and Engineering Design Review

  The radial loads of both gears are in the same plane and

a shaft is to be designed to support the spur pinion and helical gear shown in the figure on two bearings spaced 700 mm

  Neglecting potential energy effects and assuming ideal gas

air is heated at steady state as it flows through a constant area duct. at the inlet the pressure is 2.8 bar the

  What power could be transmitted by a similar shaft rotating

If the maximum shear stress is limited to one-half of its yield strength and the fillet radius is 0.3 in, what is the maximum torque that can be applied? What power could be transmitted by a similar shaft rotating at 400 rpm?

  Consider uniform potential flow past an ellipse with

consider uniform potential flow past an ellipse with thickness ratio t. use an appropriate joukowski transformation to

  Determine the exit temperature and the power input assuming

air at 100 kpa and 27degc enters an isentropic compressor at a rate of 100 ls and leaves at 1000 kpa. determine the

  Determine a the tractive force exerted by each locomotive

two 415000-lb locomotives pull 41 205000-lb coal hoppers. the train starts from rest and accelerates uniformly to a

  For a turbine efficiency of 86 determine a the amount of

air enters the compressor of a regenerative gas-turbine engine at 300 k and 100 kpa where it is compressed to 800 kpa

  After it oscillates for 50 s the displacement of the object

a 50.0 g object moves on the end of a spring with spring constant k 25.0 nm. it is released with an initial

  What is the ideal mechanical advantage of the wedge

A hydraulic shear applies 2000 lb force to a wedge. It is used to shear plate steel to rough size. The shear has a 1/4 inch thick cutting blade with a 45 degree slope. What is the ideal mechanical advantage of the wedge?

  Awheatstone bridge initially has resistances equal to r1

a wheatstone bridge initially has resistances equal to r1 200 omega r2 400 omega r3 500 omega and r4 600 omega .

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd