After pumping stops and a new equilibrium is reached the

Assignment Help Mechanical Engineering
Reference no: EM13346100

After pumping stops and a new equilibrium is reached, the tire pressure is 600 kP a and the air temperature in the tire is 20 C. a) Determine the mass [kg] of air added to the tire. B) Determine the minimum amount of work [kJ ] required to reach this end state. C) If more than the minimum work is actually used, where does this extra energy go? That is what becomes of the extra energy? 

Reference no: EM13346100

Questions Cloud

Two electronics students are discussing electrical units : two electronics students are discussing electrical units. student a says that electrical power is measured in units
Vtamin c l-ascorbic acid mw 1760 gmol is a weak acid pka : vitamin c l-ascorbic acid mw 176.0 gmol is a weak acid pka 4.863. suppose a 500.0 mg tablet is dissolved in water and
Database management principles and applications consider : database management principles and applications. consider the relational database schema for a library database
Calculate the ph resulting from mixing 1500 ml of 0800 m : calculate the ph resulting from mixing 15.00 ml of 0.800 m hio3 pka 0.77 with 45.00 ml of 0.0200 m
After pumping stops and a new equilibrium is reached the : after pumping stops and a new equilibrium is reached the tire pressure is 600 kp a and the air temperature in the tire
A robust first grader goes for swimming lessons three times : a robust first grader goes for swimming lessons three times a week and he enjoys it thoroughly. during the first week
The diameter of a neutral helium atom is about 1x10 : the diameter of a neutral helium atom is about 1x10 pm.suppose that we could line up helium atoms side by side in
Design a receiver ee determine the block diagram that : design a receiver e.e. determine the block diagram that will detect the data on a qam waveform having an m 16-point
2103 v 40 v b c qv e0pr2d r qdvpe012 r 424 m 42 a : 2103 v 40 v b c qv e0pr2d r qdvpe012 r 4.24 m 42 a parallel-plate air-gap capacitor has a capacitance of 0.14 f.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the velocity ratios that can be achieved

Determine the velocity ratios that can be achieved by the gear box in terms of number of teeth in the sun wheel  and determine which component (out of the sun wheel, planet carrier and annular wheel) has to be used as the input shaft to get the req..

  Calculate the speed of load g

Wheel of radius r is driven by an arm OA. It is driving (without slip) wheel of a radius r2 which is fixed to a drum of radius r1. Load G is attached to the rope which winds on the drum. Calculate the speed of load G if the arm OA moves at n rev/m..

  Neglect the weight of the gate and friction in the hinge

The rigid gate, is hinged at O and rests against a rigid support at B. What minimum horizontal force, P, is required to hold the gate closed if its width is 3.9 m? Neglect the weight of the gate and friction in the hinge. The back of the gate is e..

  Explain steam enters a turbine operating at steady-state

Steam enters a turbine operating at steady-state at 700 ºF and 600 lbf/in2 and leaves at 0.6 lbf/in2 with a quality of 90%. The turbine develops 12,000 hp

  Determine the unit cell volume

Beryllium has an HCP unit cell for which the ratio of the lattice parameters c/a is 1.568. If the radius of the Be atom is 0.1143 nm, (a) determine the unit cell volume, and (b) calculate the theoretical density of Be.

  What is the wall stress of the pipe

Water flows though a 20mm diameter pipe at 3L/min and static pressure of 100mmHG. What is the wall stress of the pipe. The pipe is 1.5mm thick.

  The elastic modulus of diamond is measured by applying a

the elastic modulus of diamond is measured by applying a force parallel to the body diagonal of the unit cell and

  Calculate the tensile stress required to cause yielding

if the critical resolved shear stress for yielding in aluminum is 240kpa. calculate the tensile stress required to cause yielding when the tensile axis is [001]

  Determine the absolute maximum bending stress in the beam

If the beam has square cross section of 9 in., on each side, determine the absolute maximum bending stress in the beam.

  State at least two measures that could be taken

A flat bar is to be rolls but the rolls refuse to bite (the bar is not drawn into the roll gap). State at least two measures that could be taken.

  Determine the maximum speed

A vehicle of mass 1500kg and track 1.8m has a centre of mass located centrally at 1,1m above the ground. It has to travel around a bend of 56m radius to the centre of mass.

  A 75-lb stoplight is suspended between two poles as shown

a 75-lb stoplight is suspended between two poles as shown in fignbspp3-27. neglect the weight of the flexible cables

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd