User Account

All Pages

A woman with wieght 637n lies on a bed of nails the bed has

Assignment Help Mechanical Engineering
Reference no: EM13631253

A woman with wieght 637N lies on a bed of nails. the bed has a weight of 735N and a lenght of 1.72m. the bed is held up by 2 supports, one ate the head and the other at the foot. Underneath each support is a scale. when the women lies in the bed, the scale at the foot reads 712N. how far is the center of gravity of the system from the foot of the bed of nails?

Reference no: EM13631253

Questions Cloud

An 8-m long unisulated square duct of cross sectional 02-m : an 8-m long unisulated square duct of cross sectional 0.2-m x 0.2-m and relative roughness 10-8 passes through the
Find the specific volume of steam in m3kg at 25 mpa and : find the specific volume of steam in m3kg at 2.5 mpa and 283 degrees c. what is the value predicted by the ideal gas
Water is to be pumped from a lake to a ranger station on : water is to be pumped from a lake to a ranger station on the side of the mountain. the flow rate is to be 95 galmin
A steel t-section is to be used under torsion the cross : a steel t-section is to be used under torsion. the cross section shown below has dimension bf6 in tf0.6 in d10in tw0.5
A woman with wieght 637n lies on a bed of nails the bed has : a woman with wieght 637n lies on a bed of nails. the bed has a weight of 735n and a lenght of 1.72m. the bed is held up
What is the optimal number of cases to have on hand to : a beer distributor incurs a penalty cost of 2 per case of shortage and a 1 charge per case left over in inventory at
The effective area of the hole is 114 times 10-3 m2 and is : a ship is floating on a lake. its hold is the interior space beneath its deck the hold is empty and is open to the
What is the mass of the container ignore the mass of the : a lost shipping container is found resting on the ocean floor and completely submerged. the container is 5.9 m long 2.9
Why is the reynolds number for onest of turbulence given : why is the reynolds number for onest of turbulence given by re gt 2000 in fully flowing pipes and re gt 500 in partly

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The ideal rakine cyle has steam leaves the boiler at

the ideal rakine cyle has steam leaves the boiler at 800psia and 1000f. the turbine exit is at 1.276 psia with a

  Steam enters a turbine at 120 bars and 440 0c and expands

steam enters a turbine at 120 bars and 440 0c and expands to 1 bar. at the exit entropy is 0.650 kjkg. k greater than

  Using these calculated values what would the required

using a 3 flute solid carbide 20mm diameter slot drill. with feed rate of 0.175mmtoothrev at a depth of cut of 12mm and

  The dimensions of a i beam are thicknesst flange width

the dimensions of a i beam are thicknesst flange width b10t and height 20t. determine the absolute maximum bending

  Etermine the principal stresses and maximum shearing stress

four forces are applied to a W200x35.9 rolled beam as shown. determine the principal stresses and maximum shearing stress at point a.

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  Determine the magnitude of forces t

the boat is to be pulled onto shore using two ropes. If the resultant force is to be 1000 N, directed along the keel aa , determine the magnitude of forces T, P acting in each rope at the angle teta of P so that the magnitude of P is minimum. T ac..

  Air enters a compressor operating at steady state with a

air enters a compressor operating at steady state with a volumetric flow rate of 8 m3min at 23degc and 0.12 mpa. the

  A turbine takes in 2 kgs neon at 27 degc and 200kpa with

a turbine takes in 2 kgs neon at 27 degc and 200kpa with negligible velocity. the produced work is 75 kw and 30 kw of

  Hydrogen at 25 bar 450degc enters an adiabatic turbine and

hydrogen at 25 bar 450degc enters an adiabatic turbine and expands to 2 bar 160degc with a mass flow rate of 0.2 kgs.

  Draw mohrs circle for a point on top of the cross-section

a simply supported beam of length 18 ft. is subjected to a trapezoidally distributed load that has a value of 3 kipft

  Construct the homogeneous solution

Construct the homogeneous solution in terms of four constant that could be determined from initial conditions and show the equations of motion

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd