A vertical shaft whose cross sectional area is 08 cm2 is

Assignment Help Mechanical Engineering
Reference no: EM13624296

A vertical shaft whose cross sectional area is 0.8 cm2 is attached to the top of the piston. Determine the magnitude, F, of the force acting on the shaft, in N, required if the gas pressure is 3 bar. The masses of the piston and attached shaft are 24.5 kg and 0.5 kg, respectively. The piston diameter is 10 cm. the local atmospheric pressure is 1 bar. The piston moves smoothly in the cylinder and g= 9.81 m/s2.

Reference no: EM13624296

Questions Cloud

The relationship between pressure and volume during the : oxygen o2 gas within a piston-cylinder assembly undergoes an expansion from a volume v1 0.01 m3 to a volume v2 0.03
An ice chest is constructed of 04 mm thick plain-carbon : an ice chest is constructed of 0.4 mm thick plain-carbon steel plate a 1.9 cm thick layer of styrofoam k0.033 wm c and
If the charge in part a is due to k ions charge e how many : the membrane that surrounds a certain type of living cell has a surface area of 7.1 x 10-9 m2 and a thickness of 1.6 x
Draw the power curve and compute the probability of : a firm assumes that idle time of workers in construction projects is 72 minutes give or take 20 minutes. a random
A vertical shaft whose cross sectional area is 08 cm2 is : a vertical shaft whose cross sectional area is 0.8 cm2 is attached to the top of the piston. determine the magnitude f
Consider the type of clothes dryer gas or electric : consider the type of clothes dryer gas or electric purchased by each of ve di erent customers at a certain store.a. if
Use amperes law to find the magnitude of the magnetic field : the wire in the drawing carries a current of 9.3 a. suppose that a second long straight wire is placed right next to
Estimate the magnitude of the force in both lbf and n : estimate the magnitude of the force in both lbf and n exerted by a seat belt on a 200 lb driver during a frontal
At the conclusion of the selection process what is the : one box contains six red balls and four green balls and a second box contains seven red balls and three green balls. a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What are the adavanteges and disadvantages of project

1-what are the adavanteges and disadvantages of project managment?2-what are the key charactristics all project

  Find the power to the air and how much air should be flowed

a power plant generates 150 mw of electrical power. it uses a supply of 1000 mw from a geothermal source and rejects

  Which of the following butt-weld preparations is usually

which of the following butt-weld preparations is usually the most susceptible to lack of sidewall fusion during the

  What is the efficiency of this heat engine what is the

a heat engine is composed of of a monatomic ideal gas which runs in the following cycle at point a the pressure is 2.6

  How much toque docs the motor need to supply in n-m in

a rigid well insulated container contains 10 kg of water. a motor connected to a paddle wheel is used to stir the water

  The same net magnetic flux passes through the second

two flat surfaces are exposed to a uniform horizontal magnetic field of magnitude 0.42 t. when viewed edge-on the first

  A man having the mass of 73 kg sits in the chair which is

a man having the mass of 73 kg sits in the chair which is pin-connected to the frame bc. if the man is always seated in

  If the cold-air assumptions can be applied determine how

a four cylinder two stroke diesel engine has a cut-off ratio of 1.8 and a compression ratio of 22. it operates with an

  A steel ring of mean diameter 250 mm has a square section

a steel ring of mean diameter 250 mm has a square section 2.5 mm by 2.5 mm. it is split by a narrow radial saw cut. the

  What is the most cost-effective way of acquiring the parts

Your engineering firm decides to build a prototype, and needs screw and nut fasteners as well as resistors and LEDs. There are machinists and electronics technicians available for in-house production. What is the most cost-effective way of acquiri..

  Milk enters the tank through a 005 m diameter pipe at a

a large storage tank contains 500000 l of milk. milk enters the tank through a 0.05 m diameter pipe at a velocity of 3

  Determine the volume after all the ice is melted

100 kg of liquid water at 25C and 50 kg of ice at 0C are placed in an isolated container. (a) (b) (c) Find the initial volume of the liquid-ice mixture, in m3. Determine the volume after all the ice is melted, in m3. Will the temperature of the li..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd