A venturimeter was found to be constant for rates of flow

Assignment Help Mechanical Engineering
Reference no: EM13749483

The discharge coefficient of a Venturimeter was found to be constant for rates of flow exceeding a certain value. Show that for this condition the loss of head due to friction in the convergent parts of the meter can be expressed as KQ2 m where K is a constant and Q is the rate of flow in cumecs. Obtain the value of K if the inlet and throat diameter of the Venturimeter are 0.102m and 0.05m respectively and the discharge coefficient is 0.96. 

Reference no: EM13749483

Questions Cloud

Volatility of stocks : You decide to show Alice Cartwright how beta affects the volatility of stocks. You need to go out and find 5 stocks in which you think Alice might have investment interest.
Describe a change pertaining to an it project : Imagine you work as an IT professional for a midsized company. Describe a change (i.e., a change of process, system, technique) pertaining to an IT project
Calculate the price of the house : Assume the growth rate that you calculated in #1 prevailed since 1900. Calculate the price of the house in 1900. Assume the growth rate that you calculated in #1 prevailed since 1900. Which price was paid for the house in 1964?
Examine the extent to which the two similar companies : Examine the extent to which the two (2) similar companies you researched have addressed the key issues you selected. Hypothesize two (2) potential positive outcomes for each company
A venturimeter was found to be constant for rates of flow : The discharge coefficient of a Venturimeter was found to be constant for rates of flow exceeding a certain value. Show that for this condition the loss of head due to friction in the convergent parts of the meter can be expressed as KQ2 m where K is ..
Case study of exide corporation : Exide stock price had been lagging its industry averages, so its board of directors brought in a new CEO, John Lee. Lee had brought in Ashley Novak;finance MBA who had been working for a consulting company, to replace the old CFO, and Lee asked As..
What was the salt march : What was the salt march?
What was the capital of the first anglo colony in texas : What was the capital of the first anglo colony in texas?
Discuss how and why organization should apply sdlc process : Research the process of System Development Life Cycle. Discuss how and why an organization should apply SDLC process

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Injection molding machine-what is minimum clamp tonnage

The bottom of a chair (where you sit, the ‘seat’) will be injection molded by itself in a mold. Assume the chair is a disk, 24 inches in diameter and 1/10 inch thick. If the injection pressure is 1600 psi, what is the minimum clamp tonnage you need f..

  Determine the number of bolts needed

A lap joint needs to be designed using 20-mm diameter bolts to carry a load of 120 kN on the connecting plates. If the shear stress in each rivet is not to exceed 90 MPa, determine the number of bolts needed.

  Find a transfer function between armature voltage and

a loudspeaker is modeled with the following three equations.mx bx blittecoil blxldidt ri va - blxfind a transfer

  Determine the maximum stress and the difference in tube

a tube 4cm inside and 6cm outside diameter is to be reinforced by shrinking on a tube of 8cm outside diameter. the

  Seven kilograms of air is contained in a constant

Four kilograms of water initially at 200 degree Celsius and 0.5 MPa undergo an isothermal, internally reversible compression process to the saturated liquid state. Determine the work and heat transfer involved in the process (in kJ). Sketch the proce..

  Determine the unknown properties of the perfect gas

Carbon dioxide gas (CO2) at a pressure of 15 psia and 90 degrees F. Determine the unknown properties of the perfect gas (specific volume).

  Steel reinforcement rods had been pulled to a thickness

steel reinforcement rods had been pulled to a thickness below regulatory standards. what is the effect of this

  Assumptions about the drop size and the unit cost of energy

A 1982 U.S. Department of Energy article (FS#204) states that a leak of one drip of hot water per second can cost $1.00 per month. Making reasonable assumptions about the drop size and the unit cost of energy, determine if this claim is reasonable. S..

  What are the adavanteges and disadvantages of project

1-what are the adavanteges and disadvantages of project managment?2-what are the key charactristics all project

  A car of mass 2000 kg travelling 30 degree north of east at

a car of mass 2000 kg travelling 30 degree north of east at 20 ms strikes a car of mass 3000 kg travelling 10 degree

  Write an expression for the conduction heat rate qxx use

steady-state one-dimensional conduction occurs in a rod of constant thermal conductivity k and variable cross-sectional

  Calculate the final temperature in the small cylinder

If the filling is done rapidly, calculate the final temperature in the small cylinder, (a) assume that oxygen is an ideal gas with Cv= 5R/2 and (b) using accurate thermodynamic data for oxygen.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd