A uniform bar of length l and weight w is suspended

Assignment Help Mechanical Engineering
Reference no: EM131357964

1. A uniform bar of length L and weight W is suspended symmetrically by two strings as shown in Fig.1 Set up the differential equation of motion for small angular oscillations of the bar about the vertical axis z, and determine its period.

185_Figure 1.jpg

2. Set up the differential equation of motion for the system shown in Fig.2. Determine the expression for (a) the critical damping coefficient. And (b) the natural frequency of damped oscillation.

1627_Figure 2.jpg

3. A plate of area A and weight W is attached to the end of a spring and is allowed to oscillate in a viscous fluid as shown in Fig.3. If T1 is the natural period of undamped oscillation(that is, with the system oscillatingin air), and T2 the damped period with the plate immersed in the fluid. Determine the damping coefficient  μ,where the damping force on the plate is F= 2μAv, 2A is the total surface area of the plate, and v is its velocity.

1068_Figure 3.jpg

 

4. Consider the following two degree of freedom vibration system.

529_Figure 5.jpg

The x1(t), x2(t) and x3(t) are the coordinates that measure the response of mass m1, m2 and m3.

1) First, determine the natural frequencies and mode shapes of this vibratory system. Obtain the natural frequencies and draw the corresponding mode shapes, and explain why these two mode shapes have distinctly different characteristics.

2) If there is an external excitation on the 2st mass m2, which can be expressed as Feiωt. What will be the responses of the three masses?

5. Fig.6 shows a string of length l and mass per unit length ρ is under tension T, and its upper end fixed at x = 0 and the lower end at x = l on a mass m which is supported on a spring of stiffness k and can slide in a slot in the transverse direction. Determine the equation for natural frequencies. Boundary conditions in this case are given by w(x,t)|x=0 = 0 and

-{T(∂w(x, t)/∂x) + kw(x, t)}|x=l = m(∂2w(x, t)/∂t2)|x=1

2356_Figure 6.jpg

Reference no: EM131357964

Questions Cloud

What are the points of convergence and divergence : Review Microsoft's compensation strategy using the Argosy University online library resources and the Internet. Review the organization's corporate strategy in its annual report. A link to Microsoft's most current annual report is in the Webliogra..
Separate files for the completion of assignment : This assignment consists of two (2) sections: a project introduction and a Gantt chart or project plan. You must submit both sections as separate files for the completion of this assignment. Label each file name according to the section of the assig..
Comprise justifiable argument for the use of data warehouses : CIS 500- Comprise a justifiable argument for the use of data warehouses, data centers, and data marts in order to support for business intelligence (BI) within the organizational structure.
Conduct a data-reduction exercise using the framework : Develop and apply a coding frame to interview transcripts - conduct a data-reduction exercise using the Framework approach and produce a short report of your findings and provide supporting evidence for all of your findings.
A uniform bar of length l and weight w is suspended : A uniform bar of length L and weight W is suspended symmetrically by two strings as shown in Fig.1 Set up the differential equation of motion for small angular oscillations of the bar about the vertical axis z, and determine its period.
Compute approximate values of e1 e2 g12 and ?12 : Compute approximate values of E1, E2, G12, ν12 for the composite of given exercise. Compare the results obtained using the mechanics of materials approach with the results obtained using more accurate formulas which are programmed in the accompanyi..
What is firm weighted average cost of capital : Assume that your firm's marginal tax rate is 35% and that your firm has the following capital structure: Bonds coupon rate = 6% yield-to-maturity = 5.5% Market value of bonds = $25 million Book value of bonds = $30 million. What is your firm’s Weight..
What percentage of those surveyed found nothing : A recent Gallup poll of 519 adults who flew in the past year found the following number of complaints about flying: cramped seats (45), cost (16), dislike or fear of flying (57), security measures (119), What percentage of those surveyed found noth..
Discuss about the role of the manager : Assume you are involved as an executive vice-president of Acme Corporation in the process of selecting an individual to fill the newly created position of Executive Vice-President for International Operations. This new position was created by beca..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the specific volume of superheated water vapor

Determine the specific volume of superheated water vapor at 15 MPa and 407°C, using the generalized compressibility chart. In m3/kg with four significant figures.

  How much energy is required to accelerate

How much energy (kJ) is required to accelerate a 1500 kg passenger vehicle from rest to highway speed (110 km/hr)? If it takes fifteen seconds to accelerate the vehicle, what is the average power (kW)?

  Determine the average normal stress in the shank

The long bolt passes through the 4 in. thick plate. If the force in the bolt shank is 50 lb, determine the average normal stress in the shank, the average shear stress along the cylindrical area of the late defined by the section lines a-a, and the a..

  Lead shot is formed by dropping molten lead through the

lead shot is formed by dropping molten lead through the center of a high tower. the frictional resistance of the air as

  When loaded the gages read 1900 -700 and 240 300

an equiangular strain gage rosette is mounted on a free and unloaded surface of a part made of steel. when loaded the

  For flow over a circular cylinder as shown below the

for flow over a circular cylinder as shown below the velocity outside of boundary layer can be estimated to beux 2 ug

  Value of the thermal resistance

If the fin thickness and pitch are t = 1 mm  and S = 4 mm, respectively, what is the value of the thermal resistance Rt,o for a one-half section of the fin array?

  Minimum weight design of a variable shape three-bar

minimum weight design of a variable shape three-bar truss.numerical solution using the matlab optimization toolbox

  A gate is 05 m wide and 06 m tall and is hinged at the

a gate is 0.5 m wide and 0.6 m tall and is hinged at the bottom. on one side the gate holds back a 0.5 m deep body of

  Determine the following assume that the tunnel operates

a hypersonic gun tunnel is used to generate short-duration high-speed flows and typically consists of two cylindrical

  Perfluorinated liquid with properties

Consider the microchannel chip cooling applica- tion of Problem 8.109 but now for a perfluorinated liquid with properties of cp = 1050 J/kg · K, k = 0.065 W/m · K, µ, = 0.0012 N · s/m2, and Pr = 15.

  Determine the exit temperature and pressure of the air

A. Steam enters well-insulated turbine at 7000 kPa, 600°C, with a velocity of 288 kph and leaves the turbine at 50 kPa and 150°C, at a velocity of 504 kph. The power output of the turbine is 6600 kW.  Air enters an adiabatic nozzle at 45 psia and 940..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd