User Account

All Pages

A thin flat plate is installed in a water tunnel as a

Assignment Help Mechanical Engineering
Reference no: EM13346201

A thin flat plate is installed in a water tunnel as a splitter. The plate is 0.3 m long and 1 m wide. The freestream speed is 1.6 m/s. Laminar boundary layers from on both sides of the plate. The boundary layer-velocity profile is approximated as parabolic. Determine the total viscous drag force on the plate assuming that pressure drag is negligible. 

Reference no: EM13346201

Questions Cloud

The half-life for the reaction at 550 c is 813 seconds how : the decomposition of phosphine ph3 follows first-order kinetics.4 ph3g gt p4g 6 h2gthe half-life for the reaction at
Provide the chemical reaction of an oxidation-reduction : provide the chemical reaction of an oxidation-reduction reaction that was observed to be spontaneous. provide a value
The half-lives were found to be 161 min at 199 degrees : the isomerization of methyl isocyanide ch3nc -gt ch3cn follows first-order kinetics. the half-lives were found to be
Starting with only the solid it is found that at 40c the : ammonium carbonate decomposes as followsnh4co2nh2--gt 2nh3g co2starting with only the solid it is found that at 40c
A thin flat plate is installed in a water tunnel as a : a thin flat plate is installed in a water tunnel as a splitter. the plate is 0.3 m long and 1 m wide. the freestream
An escalator has to carry 10000 persons per hour with : an escalator has to carry 10000 persons per hour with average mass of 75kg to height of 10m. if the mechanical
Then after ten to fifteen minutes it was noted that the : first 10 drops of copper ii sulfate was placed into two wells and then a piece of string that was completely saturated
The complex ion cocn6-3 absorbs a photon of wavelength : the complex ion cocn6-3 absorbs a photon of wavelength 2.90times102 nm. what is the splitting energy of this
Then 200 ml of solution a is diluted with 800 ml of : 1.0 ml of a 3.60 x 10-4 m solution of oleic acid is diluted with 9.00 ml of petroleum ether forming solution a. then

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the heat transfer by radiation

An air heater may be fabricated by coiling Nichrome wire and passing air in cross flow over the wire. Consider a heater fabricated from wire of diameter D=1 mm, L= 2m, electrical resistivity rho=10^-6 ohms, thermal conductivity k=25W/mK, and emiss..

  Determine the convection heat transfer coefficients

a 50 cm long 800 w electric resistance heating element with diameter .5 cm and surface temperature 120c is immersed in 60 kg of water temperature to 80c. also determine the convection heat transfer coefficients at the beginning and at the end of t..

  Determine the velocity va

The catapult is used to launch a ball such that it strikes the wall of the building at the maximum height of its trajectory. If it takes 1.5 s to travel from A to B, determine the velocity vA at which it was launched, the angle of release q, and t..

  What is the volume of the box

Identify the mass properties that would be used to determine an appropriate size box to package 60 ABS Plastic (0.038 lb/in3) blanks and to ship them at $1.15 per pound.

  The rigid gate oab shown in the figure below is hinged at o

the rigid gate oab shown in the figure below is hinged at o and rests against a rigid support at b. what minimum

  Explain the velocity of the ball when it reaches the highest

A ball with a mass of 0.25 kg is thrown vertically upward with an initial velocity of 10 m/s. What is the velocity of the ball when it reaches the highest point?

  The force exerted on the cue ball by the cue is horizontal

the force exerted on the cue ball by the cue is horizontal. determine the value of h for which the ball rolls without

  Determine the smallest horizontal force requirednbspto lift

determine the smallest horizontal force required to lift the 260- crate. the coefficient of static friction at all

  Determine the external moment

Vertical plane due to the action of the external moment and determine the external moment or force.

  Calculate the power output in kw

Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.

  Determine the largest load p

A knowing that the normal stress magnitude in each link is not to exceed 24 ksi, the shearing stress in pin F is not to exceed 15 ksi, and the deflection of point A is not to exceed .08 in.

  Find the velocity of the bullet and the distance

Find the velocity of the bullet and the distance it has traveled into the water after 4 seconds. Please show detailed step by step process to solution.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd