A steam turbine has extractions to provide heating steam

Assignment Help Mechanical Engineering
Reference no: EM13617505

A steam turbine has extractions to provide heating steam for the feedwater heaters in a power plant. The following parameters are known:

a. Isentropic Efficiency: .85

b. Inlet flow: 500 kg/s

c. Inlet pressure: 4500 kPa

d. Inlet Temperature: 330 C

e. Extraction 1: Pressure = 3300 kPa, flow rate=50 kg/s

f. Extraction 1: Pressure = 2200 kPa, flow rate=40 kg/s

g. Extraction 1: Pressure = 1600 kPa, flow rate=30 kg/s

h. Extraction 1: Pressure = 1200 kPa, flow rate=20 kg/s

i. Turbine Exhaust: Pressure=100 kPa

Determine the power, in MW, of the turbine.

Reference no: EM13617505

Questions Cloud

Find i the maximum pressure shown by a gauge on the cooker : 2 kg of water at 10oc and atmospheric pressure are placed in a pressure cooker and heated until the water boils at
The mean of a normal probability distribution is 60 the : the mean of a normal probability distribution is 60 the standard deviation is 5. refer to the table in appendix a.1.
Bsw corporation has a bond issue outstanding with an annual : bsw corporation has a bond issue outstanding with an annual coupon rate of 5.8 percent paid quarterly and four years
A solid disc with radius r is is spinning an object exerts : a solid disc with radius r is is spinning. an object exerts a force f at the edge of the disc to slow down the disc.
A steam turbine has extractions to provide heating steam : a steam turbine has extractions to provide heating steam for the feedwater heaters in a power plant. the following
What is the discount yield bond equivalent yield and : what is the discount yield bond equivalent yield and effective annual return on a 1 million treasury bill that
Determine the shortest time possible for the rear wheel : determine the shortest time possible for the rear wheel drive 2 mg truck to achieve a speed of 16 ms with a constant
A resistor is known to obey ohms law when there is a : a resistor is known to obey ohms law. when there is a current of 1.72 a in the resistor it has a voltage drop across
Suppose instead the data from problem 1 and 4 were taken on : suppose instead the data from problem 1 and 4 were taken on the same process thus the data are no longer independent.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the concept they understood

To solve ax = b Find a number y such that ay is integer (and possibly a factor of b) Then if k Ay = b, the answer is ky What is the concept they understood?

  A hole in an aluminum roof panel is 2748 cm2 in area at

a hole in an aluminum roof panel is 2.748 cm2 in area at 0.000degc. what is the magnitude of the change to its area

  Determine the radius r of an impurity atom that will fit

determine the radius r of an impurity atom that will fit into a tetrahedral site of bcc ironr1.241 angstroms crystal

  Consider some hypothetical x - y - ion pair for which the

consider some hypothetical x - y - ion pair for which the equilibrium interionic spacing and bonding energy values are

  Determine a the enthalpy of r-134a at the exit b the

r-134a is throttled from 1200kpa and 40oc to 200kpa. it is known that heat of 5kjkg is lost from r-134a to the

  Calculate the speed at which the ball leaves the spring

A small steel ball bearing with a mass of 13 g is on a short compressed spring. When aimed vertically and suddenly released, the spring sends the bearing to a height of 1.35 m. Calculate the speed at which the ball leaves the spring.

  Two kilograms of refrigerant134a initially at 2 bar and

two kilograms of refrigerant134a initially at 2 bar and occupying a volume of 0.12 m3 undergoes a process at constant

  An electric motor of total weight 3330 pounds is mounted on

an electric motor of total weight 3330 pounds is mounted on a simply supported beam with an overhang as shown

  02 m3 of saturated liquid r-134a in a piston cylinder is

0.2 m3 of saturated liquid r-134a in a piston cylinder is heated at a constant pressure of 800kpa to 50 dcg c. what is

  What is the proeutectoid phase

Consider 1.0 kg of austenite containing 1.15 wt% C, cooled to below 727 degrees Celcius (1341 degrees Farenheit).

  Determine a the work of the adiabatic process and b the

a gas in a cylinder fitted with a piston undergoes a cycle composed of three processes. first the gas expands at

  Find the volume of the ring-shaped solid that remains

A cylindrical drill with radius r1 is used to bore vertically a hole through the centre of a sphere of radius r2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd