A single-effect evaporator system with thermal

Assignment Help Mechanical Engineering
Reference no: EM13626794

A single-effect evaporator system with thermal recompression is being used to concentrate skim milk from an initial total solids content of 9.5%to 25%. The product feed temperature is 5°C and the evaporation is occurring at 57.38 kPa. The heating medium for the evaporator is steam at 100°C. If the product feed rate is 8250 kg/hr, calculate (i) the steam economy, and (ii) efficiency improvement achieved by the use of mechanical recompression system.

Reference no: EM13626794

Questions Cloud

A particle with mass m is confined on a line with length l : a particle with mass m is confined on a line with length l. with uncertainty principle estimate the minimum energy of
If a plane wave is reflected from the ocean floor at normal : if a plane wave is reflected from the ocean floor at normal incidence with a level 20 db below that of the incident
The length of conversations between supervisors and workers : the length of conversations between supervisors and workers in a certain manufacturing industry is normally distributed
Calculate the number of vacancies per cubic meter in some : calculate the number of vacancies per cubic meter in some metal at 688degc. the energy for vacancy formation is 0.87
A single-effect evaporator system with thermal : a single-effect evaporator system with thermal recompression is being used to concentrate skim milk from an initial
Name the scale of measurement that applies to each of the : name the scale of measurement that applies to each of the following situationsa. james hall in 68.5 feet tall-b. a
A rock weighing 98 n is thrown downward with a velocity of : a rock weighing 98 n is thrown downward with a velocity of 20 ms from the top of a 140 m tall building. what is the
The room is 3 m x 4 m x 26 meters high if we treat the room : 0.25 kg of red-hot 700 c coals are taken from the fireplace and left in the middle of a room. the room is 3 m x 4 m x
The acme light bulb company claims that the lifetimes of : the acme light bulb company claims that the lifetimes of its 100-watt light bulbs follow a normal distribution with a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate a the mass of the bubble b the final temperature

a 2 mm diameter spherical air bubble is suspended in an insulating fluid . with a focused laser the bubble is heated so

  The gas in then compressed to 200 psia in a reversible

an insulated cylinder having an initial volume of 2 ft3 contains carbon dioxide at 15 psia and 440degf. the gas in then

  A particle which moves with curvilinear motion has

a particle which moves with curvilinear motion has coordinates in meters which vary with time t in seconds according to

  Calculate the rate of change of heat with the cylinder

how do i calculate the rate of change of heat with the cylinder, and the vertical temperature distribution along the cylinder's wall.

  Bubble dynamics underneath a downward facing anode

Bubble dynamics underneath a downward facing anode in Hall-Heroult cell. Experimental using Hall-heroult process.Analysis by using High Speed Camera and ANSYS Model.

  A 2-kw pump is used to pump kerosene rho 0820 kgl from a

a 2-kw pump is used to pump kerosene rho 0.820 kgl from a tank on the ground to another tank 30 m above the ground.

  Two perfectely black squares 10 ft x 10 ft are spaced 20

two perfectely black squares 10 ft x 10 ft are spaced 20 feet apart. what is the net rate of heat exchange between them

  Suppose you have a choice between a straight triangular or

suppose you have a choice between a straight triangular or rectangular fin constructed of aluminum with a base

  If we can achieve 10percent of the maximum theoretical work

a flat plate solar collector is to be considered as a means to drive a pump to irrigate crops. this will be used in

  Ways to ensure relevant base and safety loads

All calculations and assumptions must be provided together with a full explanation of all the terms

  If a convection coefficient of 500 wm2middotk is maintained

as part of a heat treatment process cylindrical 304 stainless steel rods of 100-mm diameter are cooled from an initial

  A particular system obeys the relation uau-2expsr n moles

a particular system obeys the relation uau-2expsr n moles of this substance initially at temperature to and pressure po

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd