User Account

All Pages

A section of magnesium alloy is being tested

Assignment Help Mechanical Engineering
Reference no: EM13956854

A section of Magnesium alloy is being tested .It is subjected to 12 kN compression force.The length is 50 mm.The cross section is 10 mm by 10 mm.The longitudinal strain is 1.5*10^-3. The poisson´s ratio for the material is 0.35

a) Find the average normal stress at the instant when the load is applied

B)Find the deformation longitudinal

c)Find the height and width of the cross section after the compression.

Reference no: EM13956854

Questions Cloud

Compute vertical component of force supported by hitch at a : The loaded trailer has a mass of 900 kg with a center of mass at G and is attached at A to a rear bumper hitch. If the car and trailer reach a velocity of 60 km/hr on a level road in a distance of 30 m from rest with constant acceleration, compute..
Members of several professional boards and associations : Engineers can become members of several professional boards and associations. Each has its own requirements and benefits of membership [http://www.onwibe.ca]. Technical societies are useful and important for professionals. Technical societies are ..
A thin plate section of an airplane is uniformly deformed : A thin  plate section of an airplane is uniformly deformed  0.3 mm in one corner (dispalcement  to the rigth) ,  0.4 mm in one corner (displacement accendent) .the dimentions: h = 300 mm
The rectangular test section of material is slowly : The rectangular test section of material is slowly loaded with a 450 kN axial load. The original cross-section is 25 mm by 100 mm. The original length is 2 meters. Once fully loaded, the 100 mm side measures 99.96 mm and the length has increased by 2..
A section of magnesium alloy is being tested : A section of Magnesium alloy is being tested .It is subjected to 12 kN compression force.The length is 50 mm.The cross section is 10 mm by 10 mm.The longitudinal strain is 1.5*10^-3. The poisson´s ratio for the material is 0.35
From the e-activity, examine some of the steps : From the e-Activity, examine some of the steps that are involved in designing goods and services. Select two services or two products that are currently on the market. Use Exhibit 6.1 from Chapter 6 of the text to compare and contrast each step, a..
What is the probability that both are defective : In a shipment of 20 televisions, 5 are defective. If 2 television sets are randomly selected and tested without replacement, what is the probability that both are defective?
A 4 inch diameter composite shaft is subjected : A 4 inch diameter composite shaft is subjected to the torques shown below. The sections are perfectly bonded rigidly together. Use GSTEEL= 11,600 ksi and GALUMINUM =4000 ksi. Determine the maximum shearing stress in the shaft and the magnitude of the..
Rotation of bar oa is controlled by the lead screw : Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v to collar C and causes pin P to travel along the smooth slot. Determine the values of r dot and theta dot, where r = OP, if h = 160mm, x= 120mm and v = 25 mm/s a..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What equal amount can you withdraw from the account at the

today you have a savings account of 15 620. based on an annual interest rate of 4.2 what equal amount can you withdraw

  Steam enters a well-insulated turbine at 10bar 300oc and

steam enters a well-insulated turbine at 10bar 300oc and 50ms and exits at 1bar and 100ms. calculate the steady-state

  Calculate heat and work interactions with the surrounding

A piston-cylinder assembly initially contains 4 mol of substance X in vapor phase at 0.8 bar and 373 K. The vapor is compressed isothermally and reversibly until the first droplet of liquid forms.

  A piston-cylinder arrangement initially contains water

A piston-cylinder arrangement initially contains water at P = 300 psia and T = 500   oF. The piston is moved to a final position where the volume is twice the initial volume. During the piston movement there is a heat transfer to the water in such a ..

  Neglecting ke and pe changes and assuming ideal gas

air enters an insulated turbine operating at a steady state at 5 bar 1000k and exits at 1 bar 500k. neglecting ke and

  Five percent of this flow is diverted for the feedwater

an isentropic steam turbine processes 5kgs of steam at 4 mpa which is exhausted at 50 kpa and 100degc. five percent of

  Determine the initial temperature

A frictionless piston-cylinder contains 3.0 kg of H2O and is initially at 300 kPa. The initial volume is 1.0 m3. The water is heated until the temperature is 300 C. If the volume within the system reaches 1.5 m3, the piston hits a set of stops and is..

  Determine the magnitude of the particles acceleration

A particle travels around a circular path having a radius of 66m. It is initially traveling with a speed of 10 m / s and its speed then increases at a rate of v = (0.05v) m /s2. Determine the magnitude of the particle's acceleration four seconds late..

  Associated supplies are expected to cost 10000 per year the

a consulting firm is contemplating the purchase of a btu meter to measure the cooling loads on chillers at a purchase

  The average radius of the wheel is 183 m and the jet

a pelton wheel is used to produce hydroelectric power. the average radius of the wheel is 1.83 m and the jet velocity

  Drinking water needs of an office are met by large water

The drinking water needs of an office are met by large water bottles. One end of a 0.6 cm diameter plastic hose is inserted into the bottle placed on a high stand, while the other end with on/off valve is maintained 0.6 m below the bottom of the bott..

  Steam at 160 bar 480degc enters a two-stage turbine

steam at 160 bar 480degc enters a two-stage turbine operating at steady sate with a volumetricnbspflow rate of 800

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd