A secondary settling tank is to be designed for a municipal

Assignment Help Mechanical Engineering
Reference no: EM13637757

A secondary settling tank is to be designed for a municipal wastewater treatment facility. The influent TSS is 1,000 mg/L and the average design flow is 1.5 MGD (peaking factor =2) and Qe/Q = 1. State regulations require that the overflow rate be no more than 600 gpd/ft2 for average daily flow and 2000 gpd/ ft2 for peak hourly flow and effluent TSS = 10 mg/L. The detention time required at average flow is 2 hours. Determine the following:

The diameter of the settling tank if it were circular (1 ft increments)?

List one advantage and one disadvantage to circular tanks.

The weir loading rate at peak flow if weirs are set 2 feet in from the tank diameter.

Reference no: EM13637757

Questions Cloud

If you want to change the buffer composition of aprotein : 1. a 100 kda protein is found to have a diffusioncoefficient value of 9.6 x 10-7 in water at 37 cm2sdegrees c. assuming
This was repeated three times for each participant and the : some researchers in understanding g-loads on humans are interested in methods that can be used to assist pilots
Two wires are identical except that one is aluminum and one : two wires are identical except that one is aluminum and one is copper. the aluminum wire has a resistance of 0.832.
A solution made up of 150 g of benzene and 251 g of solute : a solution made up of 150 g of benzene and 25.1 g of solute has afreezing point of -1.920c. determine the
A secondary settling tank is to be designed for a municipal : a secondary settling tank is to be designed for a municipal wastewater treatment facility. the influent tss is 1000 mgl
A group of hikers hears an echo 400 s after shouting if the : a group of hikers hears an echo 4.00 s after shouting. if the temperature is 18.0degc how far away is the mountain that
How many kilograms of methane gas must be discharged in a : how many kilograms of methane gas must be discharged in a room with a volume of 306 cubic meters to reach the lower
Some nitrogen is allowed to escape until the pressure in : a 20-m3 tank contains nitrogen at 23degc and 600 kpa. some nitrogen is allowed to escape until the pressure in the tank
Two copper wires one three times the diameter of the other : two copper wires one three times the diameter of the other have the same current flowing through them. if the thinner

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If a rod of 1025 steel 05 m 197 in long is heated from 20

aif a rod of 1025 steel 0.5 m 19.7 in long is heated from 20 to 80 deg c 68 to 176 deg f while its ends are maintained

  Provide a 3d sketch of the plane 112 in a bcc crystal and

consider the 112lt111gt slip system in bcc crystals1. provide a 3d sketch of the plane 112 in a bcc crystal and

  What is engineering strain modulus of elasticity what is

an aluminum alloy specimen of .562 diameter and 2gauge length was subjected to loads p resulting in gauge lengths l as

  Sketch a fatigue crack growth curve based on the paris law

sketch a fatigue crack growth curve based on the paris law. how does a change in the ratio of the minimum stressmaximum

  A small motor weighing 193 lbs is mounted on 4 springs in

a small motor weighing 19.3 lbs is mounted on 4 springs in parallel in such a manner that only vertical motion is

  Calculate the internal energy changes associated with the

measurement of the electrical resistivity of gold wires have indicated that the equilibrium vacancy concentration

  Determine the minimum coefficient of static friction

if the coefficient of static friction between the crate and ground is 0.3 determine the minimum coefficient of static

  The oil is flowing under a pressure gradient of 196 pam

oil viscosity 0.003 pa s specific gravity 0.85 is confined between two concentric circular cylinders of infinite

  The pressure in a garden hose is 60 psi and the hose is 15

the pressure in a garden hose is 60 psi. and the hose is 1.5 cm in inner diameter. the water exits in a stream 3mm in

  Determine the tensile strength of this alloy compute the

a specimen of magnesium having a rectangular cross section of dimensions 3.2 mm 19.1 mm 1818 in. 3434in. is deformed in

  Draw a complete schematic diagram for each of the two

consider the steady operation of a refrigeration package for a shipping container on a train truck or ship. the package

  Assume that the tests indicated that a tensile stress of

an internal crack has been detected by means of x-rays in the shell of a large cylindrical pressure vessel. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd