A river has a steady speed of 0461 ms a student swims

Assignment Help Mechanical Engineering
Reference no: EM13643470

A river has a steady speed of 0.461 m/s. A student swims upstream a distance of 1.00 km and swims back to the starting point.

(a) If the student can swim at a speed of 1.29 m/s in still water, how long does the trip take?

(b) How much time is required in still water for the same length swim?

(c) Intuitively, why does the swim take longer when there is a current?

 

Reference no: EM13643470

Questions Cloud

A diverging lens has a focal length of -32 cm an object is : a diverging lens has a focal length of -32 cm. an object is placed 27 cm in front of this lens. calculate a the image
Two nanow wires are separated by 12 nm as measured by stm : two nanow wires are separated by 1.2 nm as measured by stm. inside the wires the potential energy is zero but between
An rl circuit consists of a resistor r68 onmusigma an : an rl circuit consists of a resistor r68 onmusigma an inductor l31 mh and an ac generator with an rms voltage of 120 v.
Gas is confined in a tank at a pressure of 10 x 108 pa and : gas is confined in a tank at a pressure of 1.0 x 108 pa and a temperature of 15.0 c. if half the gas is withdrawn and
A river has a steady speed of 0461 ms a student swims : a river has a steady speed of 0.461 ms. a student swims upstream a distance of 1.00 km and swims back to the starting
A 105 -muf capacitor is connected to an ac generator with : a 105 -muf capacitor is connected to an ac generator with an rms voltage of 20.0 v and a frequency of 100.0 hz. what is
A what are the x and y components of the velocity of the : a ball is launched into the air at an angle of 60 above the horizontal with a speed of 21.0 ms. a what are the x and y
If the speedboat travels 584 kmh in what direction should : a coast guard cutter detects an unidentified ship at a distance of 19.6 km in the direction 17.8deg east of north. the
How many electrons must be removed from a and put onto b to : two small objects a and b are fixed in place and separated by 3.15 cm in a vacuum. object a has a charge of 2.02 microc

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the optimal pressures

determine the optimal pressures, temperatures, and fraction of steam extracted to maximize thermal efficiency.

  Knowing the mass center of the automobile and driver is 2

a stunt driver proposes to drive a small automobile at the speed of 45 mihr on the vertical wall of a circular pit of

  The building is estimated to be losing heat at a rate of

a heat pump is to be used to heat a building during the winter. the building is to be maintained at 22.9oc at all

  The water in a is cooled to maintain its initial

a rigid tank with a total volume of 0.05m3 contains a movable piston separating the vessel into two compartments each

  You have decided to design the beam with 1040 hr steel

a cantilever beam with round cross section is loaded at the tip with a transverse force of 1000 lb. the beam is also

  How does the energy use for the typical family vehicle

how does the energy use for the typical family vehicle compare with that for the typical hot water heater? what are the

  Sketch the ttt diagram for a typical high hardenability

sketch the ttt diagram for a typical high hardenability fefe3c alloy with addition elements such as ni mn n etc. in

  If the motorcycle accelerates at 6 fts2 until reaching a

a motorcycle is traveling at 60 fts a truck is also traveling at the same velocity. if the motorcycle accelerates at 6

  The stone is released from rest as it falls down the wire

a frictionless pulley has the shape of a uniform solid disk of mass 6.00kg and radius 19.0cm . a 3.40kg stone is

  The uniform disk of mass pivots freely on the cart of mass

the uniform disk of mass pivots freely on the cart of mass. determine the acceleration of the assembly and the angular

  A bar of steel 3 in 762mm in diameter is to be machined at

1 a bar of steel 3 in 76.2mm in diameter is to be machined at 90 fpm 0.5 msec. what spindle speed should be

  What can be concluded about ixy if in addition to the first

if ixiy in a given system of coordinates what can be concluded about ixy? what can be concluded about ixy if in

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd