A rectangular intake air duct is 36 in wide and 24 in high

Assignment Help Mechanical Engineering
Reference no: EM13345661

A rectangular intake air duct is 36 in. wide and 24 in. high. It runs for over 300 ft inside a warehouse and is at 50 F, but one end of the duct opens to the outside where outside air can enter the duct. If 120 cfm ( cubic feet per minute ) of outside air at 12 F enters the duct, estimate the air temperature 200 ft inside the duct.

Reference no: EM13345661

Questions Cloud

Octane has a density of 0692gml at 20 c how many grams of : octane has a density of 0.692gml at 20 c. how many grams of o2 are required to burn 1.00 gal of
A 100- lightbulb is placed in a cylinder equipped with a : a 100- lightbulb is placed in a cylinder equipped with a moveable piston. the lightbulb is turned on for 2.0times10-2
Calculate an approximate heat of reaction for the : calculate an approximate heat of reaction for the combustion of one mole of methane gas ch4 to form gaseous h2o and
Thomas poured 25 ml of 60 m hcl into a large bottle he then : thomas poured 25 ml of .60 m hcl into a large bottle. he then added enough water so that the new diluted concentration
A rectangular intake air duct is 36 in wide and 24 in high : a rectangular intake air duct is 36 in. wide and 24 in. high. it runs for over 300 ft inside a warehouse and is at 50 f
A series cct comprises of l159mh and r10ohm and a variable : a series cct comprises of l159mh and r10ohm and a variable c connected to 5mv sinusoidal supply f1mhz.what value of
The vessel contains 200 moles of nitrogen 200 moles of : three gases nitrogen helium and krypton are confined in a 4.00 l vessel at a pressure of 14.0 atm. the vessel contains
A 235ml solution is prepared with 418 millimoles of an : a 235ml solution is prepared with 41.8 millimoles of an unknown sodium salt of a deprotonated organic acid nax. if the
More realistically the principal components of meat are fat : this experiment separates meat into an acetone-soluble part and an acetone-insoluble part. the calculations are based

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Vital information about overall heat transfer coefficient

Important information about Overall Heat Transfer Coefficient A copper sphere of internal diameter 2 m and wall thickness 40 mm is insulated with 75 mm of expanded polystyrene

  If the columns cross sectional area were uniform the

suppose that you want to design a column to support a uniform compressive stress stress naught. if the columns cross

  Determine the final velocity

Determine the Final Velocity, An object whose mass is 1 lb has a velocity of 100 ft/s. How would I determine the final velocity, in ft/s, if the kinetic energy of the object decreases

  Air at the rate of 18 kgs is drawn into the compressor of a

air at the rate of 18 kgs is drawn into the compressor of a jet engine at 55 kpa and -23oc and is compressed reversibly

  Determine the heat transfer by radiation

An air heater may be fabricated by coiling Nichrome wire and passing air in cross flow over the wire. Consider a heater fabricated from wire of diameter D=1 mm, L= 2m, electrical resistivity rho=10^-6 ohms, thermal conductivity k=25W/mK, and emiss..

  What is a parting line or parting surface

1. What is a parting line or parting surface? 2. What is fluidity? 3. What type of shape modifications or allowances are generally incorporated into a casting pattern?

  Prepare a journal paper on renewable energy

Prepare a Journal paper on Renewable Energy

  Estimate the minimum bar diameter to prevent fatigue failure

Estimate the minimum bar diameter to prevent fatigue failure.

  The elastic modulus of diamond is measured by applying a

the elastic modulus of diamond is measured by applying a force parallel to the body diagonal of the unit cell and

  Advanced stress analysis assignment

Advanced Stress Analysis Assignment

  Calculate how far from the fulcrum the tweezer

Using static equilibrium calculations, calculate how far from the fulcrum the tweezers must be held to avoid damaging the sliver.

  A combined gas-vapor power plant operates as shown in

a combined gas-vapor power plant operates as shown in fig.9.94. pressure and temperature data are given at principal

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd