A projectile is fired at an angle of 48 degrees the initial

Assignment Help Mechanical Engineering
Reference no: EM13636732

1- A car starts rest and with constant acceleration achieves a velocity of 15 m/s. when it travels of 200 m, determine the acceleration of the car and the time required.

2- A projectile is fired at an angle of 48 degrees. The initial velocity of the projectile is 32 m/s. determine the range and the maximum height attained if the trajectory is symmetrical.

Reference no: EM13636732

Questions Cloud

Determine the smallest allowable dimensions a and b of the : two blocks of rubber with a modulus of rigidity g 5 12 mpa are bonded to rigid supports and to a plate ab. knowing that
A car is travelling alonna highway with a speed of 25 ms : a car is travelling alonna highway with a speed of 2.5 ms when the driver notices an obstruction 1.80 x 102m directly
Q1 what must the charge sign and magnitude of a particle : q1. what must the charge sign and magnitude of a particle of mass 1.47 g be for it to remain stationary when placed in
A technician monitoring a group of five computers in an : a technician monitoring a group of five computers in an automated manufacturing facility. it takes an average of 15
A projectile is fired at an angle of 48 degrees the initial : 1- a car starts rest and with constant acceleration achieves a velocity of 15 ms. when it travels of 200 m determine
A what is the wavelength of a 20 mhz ultrasound wave : a what is the wavelength of a 2.0 mhz ultrasound wave traveling through aluminum?b what is the frequency of
If the rolling frictional force is determined to be 47500 n : 1 a car with a projected frontal area of 1.8 m2 is traveling at 136 kph. if the drag coefficient of the car is 0.45 and
The estimate of the population proportions is to be within : the estimate of the population proportions is to be within plus or minus .10 with a 95 percent level of confidence. the
An astronaut must journey to a distant planet which is 210 : an astronaut must journey to a distant planet which is 210 light years from earth. what speed will be necessary if the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  One car p heading north begins at rest and accelerates with

one car p heading north begins at rest and accelerates with acceleration a. the other car q begins with a velocity of

  What is the maximum possible power per unit mass flow rate

the elevation change available at the grand coulee dam is 330 feet. what is the maximum possible power per unit mass

  Briefly explain how this cathodic protection of tin cans is

tin cans are made of a steel the inside of which is cated with a thin layer of tin. the tin protects the steel from

  The gauge senses axial strain the bridge output is 1 mv for

a strain gauge that has a nominal resistance of 350 ohms and a gauge factor of 1.8 is mounted in an equal-arm bridge

  A 1 kg block of copper at 350degc is quenched in a 10 kg

a 1 kg block of copper at 350degc is quenched in a 10 kg oil bath initially at ambient temperature of 20degc. calculate

  Each turbine stage operates with an isentropic efficiency

water is the working fluid in a vapor power cycle with superheat and reheat. superheated vapor enters the first turbine

  An outdoor track is 420 ft in diameter a runner increases

an outdoor track is 420 ft in diameter. a runner increases her speed at a constant rate from 14 to 24 fts over a

  Obtain a plot of the approximate transfer function model

the volume of a hemispherical storage tank as a function of its height is given by vt pirh2t - pi3h3t where r is the

  How does data screening differ from data cleaning

.How does data screening differ from data cleaning?

  What would happen if the air filter was partially choked

What would happen if the air filter was partially choked. If the piston rings were leaking state what you would expect the results of a, b, c, and d above would be.

  A hollow shaft has an outsaid diameter of 35 mm and an

a hollow shaft has an outsaid diameter of 35 mm and an insaid diameter of 25 mm complute the torsional shear stress in

  Engineering of materials i need you to write a report about

i need you to write a report about precipitation hardening of aluminum alloys . i will attach the report format which

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd