Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Which of the following statements are true? I. A process is capable with a Cp ot Pp = 1.0 II. A process may be acceptable with a Cp or Pp = 1.0 III. A Cp or Pp of 1.0 means the process variation is equal to the specification spread IV. A Cp or Pp of 1.0 means Cpk or Ppk = 2.0 A I only B II only C I, II, and III only D I, II, III, and IV Which of the following statements is true? A Shifts, trends, and points out of control can be determined on the range portion of an X-bar, R control chart B Specifications should be drawn on a control chart so that bad products can be detected C An X-bar, R chart is the best choice to use when one does not have rational subgroups D None of the above A way to avoid bias in a Measurement System Evaluation (MSE) study is to A Mix up the order of the samples under study so that the operators are not biased with the measurement that they got the last time they measured the part B Use only calibrated measurement devices C Use a different measurement device for each of the three (or more) operators D Reset the whole measurement system between each of the trials A Cp of 0.70 means A The process is out of control B The specifications are 70% of the process C The process is acceptable D All of the above When using pre-control while running, what should you do when the first piece you check falls in the yellow? A Stop running and return to setup rules B Keep running, since you are still within spec C Check the second piece D Reset your limits You are operating a concession stand selling hamburgers, hot dogs, french fries, and fountain drinks. Your processes are designed to prepare all food items to the proper internal temperature with a desirable external appearance. Which of the following items would you most likely deem as defective? A An undercooked hamburger B A batch of unevenly browned french fries C An underweight hamburger D A fountain drink with excess ice E All of the above Which of the following statements regarding the normal curve is NOT true? A It indicates that the process is normally distributed B It indicates that no factor or combination of factors is unduly influencing the process C It says nothing about the center of the process variation D It is a Gaussian distribution According to Six Sigma philosophy A Cp or Pp and Cpk or Ppk should be greater than 1.33 B Cp or Pp and Cpk or Ppk should be greater than 1.50 C Standard deviation is greater than 6 D Standard deviation is less than 6 Using the Box Cox Transformation formula, if the original value x = 3 and λ = 2, what is the resulting transformed value? A 9 B 8 C 2/3 D 1.5
Calculate the torque on the center of mass of the rod alone with respect to the pivot point.(in N*m)? Calculate the unknown mass.(in kg).
A copper bar is moved to the right while its axis is maintained in a direction perpendicular to a magnetic field, what is the direction of the magnetic field
Find what is the lift due to Bernoulli principle on a wing of area 66.6 m2 if the air passes over the top and bottom surfaces at speeds of 264 m/s and 163 m/s, correspondingly
Refrigerant-22 enters a turbine at 300 psi, 280°F, 2000 ft3/hr. The exit is at 15 psi, 10°F. Find the mass flow rate
The 40 kg wheel of an airplane flying at 248 m/s at an altitude of 7400 m falls off during a flight. If the wheel hits the ground at 377 m/s, how much work was done on the wheel by air resistance
the coefficient of static friction is 0.26. If you apply the minimum force needed to get the refrigerator to move, illustrate what will the acceleration then be?
A fighter jet is launched from an aircraft carrier with the aid of its own engines and a steam-powered catapult. The thrust of its engines is 4.72 x 105 N. What is the work done on the jet by the catapult
An electromagnetic wave of intensity 240 W/m2 is incident normally on a rectangular card with sides of 19 cm and 31 cm that reflects the entire radiation incident on it. Discover the force exerted by the electromagnetic wave on the card if the radiat..
A steel cable has a cross-sectional area 3.44 × 10-3 m2 and is kept under a tension of 1.53 × 104 N. The density of steel is 7860 kg/m3. Note that this value is not the linear density of the cable. At what speed does a transverse wave move along t..
a car tyre is pumped up to 230 kpa. what is the volume of air at atmospheric pressure 100kpa that must be pumped into a
In a calorimetry experiment an unknown amount of steam at 100 C is added to 1.5 kg of ice at 0C in a well insulated and sealed container. What is the mass of steam which was added to the ice
An oil slick on water is 105 nanometers thick and illuminated by white light at an incidence angle of 0.0° to its surface. Find the most constructively reflected wavelength
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd