A piston-cylinder device contains 08 kg of an ideal gas the

Assignment Help Mechanical Engineering
Reference no: EM13626009

A piston-cylinder device contains 0.8 kg of an ideal gas. The gas is cooled at constant pressure until its temperature decreases by 10C. During the cooling process, 16.6 kJ of work occurs. The specific heat ratio of the gas is 1.667.

(a) What is the molecular weight (kg/kmol) of the ideal gas?

(b) Calculate change in internal energy (kJ) of the ideal gas.

(c) Find change in enthalpy (kJ) of the ideal gas.

Reference no: EM13626009

Questions Cloud

A how much voltage is induced in the loop b if b is : 1. a double loop of wire of radius 40 mm lies in a plane perpendicular to a uniform magnetic field. the field changes
What is the liquid composition leaving the sixth : a distillation column is separating phenol from p-cresol at 1 atm pressure. the distilshylate composition desired is
Is this the same as the air at 1000mb on the windward side : a chinook wind blowing at 800mb has a temperature of 311k and a mixing ratio of 4gkg. is this the same as the air at
Information regarding the act scores of samples of students : information regarding the act scores of samples of students in three differentmajors is given
A piston-cylinder device contains 08 kg of an ideal gas the : a piston-cylinder device contains 0.8 kg of an ideal gas. the gas is cooled at constant pressure until its temperature
A chi-square test for independence is used to evaluate the : a chi-square test for independence is used to evaluate the relationship between two variables. if both variables are
Assume the ladder is uniform and has a mass of 152 kg while : 1 the ladder is 3.8 m long and the person is standing 1.1 m up the lenght of the ladder. the ladder makes an angle if
Discuss the possible corrosion cells that might be created : two sheets of a 1040 steel are joined together with an aluminum rivet. discuss the possible corrosion cells that might
If the wet-bulb temperature of a parcel at 1000mb is 288k : if the wet-bulb temperature of a parcel at 1000mb is 288k and its mixing ratio is 6gkg. find the relative humidity of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Water flows through a pipe ab 12 m diameter at 3 ms and

water flows through a pipe ab 1.2 m diameter at 3 ms and then passes through a pipe bc 1.5 mdiameter. at c the pipe

  Heat transfer occurs until the volume on the inside of the

a piston-cylinder device contains 1 kg of h2o. the water is at 800oc and a pressure of 20 mpa. heat transfer occurs

  The rest exits through a diameter of 15 m with a pressure

steam at 80 bar 440oc enters a turbine at 1operating at steady state with a volumetric flow rate of 236 m3min. twenty

  Determine the minimum mass in kg of a 24 in long tension

determine the minimum mass in kg of a 24 in long tension member that must support a load of 1000 lbs manufactured from

  A copper rod 50mm long and 5mm in diameter extends

a copper rod 50mm long and 5mm in diameter extends horizontally from a casting at 300 c. the rod is in an air

  Wat is the time expression for the motor response if the

the 500 lbf motor is supported on springs with a total stiffness of 5000 lbfin. the springs have a damping ratio of

  The water side of the wall of a 70-m long dam is quarter

the water side of the wall of a 70-m long dam is quarter circle with radius of 7-m. determine the hydrostatic force on

  The chain and lever attached to the gate have negligible

a gate with a circular cross section is held close by a lever 1 m long attached to a buoyant cylinder. the cylinder is

  The average radius of the wheel is 183 m and the jet

a pelton wheel is used to produce hydroelectric power. the average radius of the wheel is 1.83 m and the jet velocity

  What are the properties of petrol

what are the properties of petrol that it make particularly suitable for the use as fuel in a motor vehicle.

  Calculate the velocity component at the point 2 05 0

a velocity field is specified as v ax2i bxyj where a 2 m-1s-1 b -4 m-1s-1 and the coordinates are measured in

  What is the solar flux absorbed by the abdorber plate given

a solar collector is made of a cover plate then a 5 cm air gap and then an absorber plate with insulation on the back

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd