A nonwetting metal surface that is at temperature ts -15

Assignment Help Mechanical Engineering
Reference no: EM13605855

A small water droplet of diameter D=100 micro meter and temperature T_mp = 0 deg C falls on a nonwetting metal surface that is at temperature T_s = -15 deg C. Determine how long it will take for the droplet to freeze completely. The latent heat of fusion is h_sf = 334 kJ/kg.

Reference no: EM13605855

Questions Cloud

Knowing that it strikes the water 4 s after release : a stone is thrown vertically upward from a point on a bridge located 40 m above the water. knowing that it strikes the
Scott and quick are accountants for millenium computers : scott and quick are accountants for millenium computers. they disagree over the following transactions that occurred
In a study investigating the effect of car speed on : in a study investigating the effect of car speed on accident severity 5000 reports of fatal automobile accidents were
Air that initially occupies 049 m3 at a gauge pressure of : air that initially occupies 0.49 m3 at a gauge pressure of 63 kpa is expanded isothermally to a pressure of 101.3 kpa
A nonwetting metal surface that is at temperature ts -15 : a small water droplet of diameter d100 micro meter and temperature tmp 0 deg c falls on a nonwetting metal surface
The volume of an ideal gas is adiabatically reduced from : the volume of an ideal gas is adiabatically reduced from 241 l to 78.5 l. the initial pressure and temperature are 1.00
Primara corporation has a standard cost system in which it : primara corporation has a standard cost system in which it applies overhead to products based on the standard direct
Nevada mines purchased a piece of land and the mineral : nevada mines purchased a piece of land and the mineral rights for 3200000. company engineers that the property contains
What is the probability that a randomly chosen student : undergrad students in a section of stat 225 are classified as lower classmen freshman and sophomores and upper classmen

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A small mechanical part in a complicated machine moves such

a small mechanical part in a complicated machine moves such that its position relative to a fixed frame of reference is

  Using variable specific heat method

1. A Brayton cycle uses air and produces a net work of 14000 Btu/s with an inlet state of 60°F, 14.7 psi and a compression ratio of 16. The heat added in the combustion process is 400 Btu/lbm. If the thermal efficiency is 0.547 Determine: Using va..

  Calculate the tensile stress required to cause yielding

if the critical resolved shear stress for yielding in aluminum is 240kpa. calculate the tensile stress required to cause yielding when the tensile axis is [001]

  Explain the distortion energy failure theory

How do I find the factor of safety using the distortion energy failure theory?

  Find the speed of the block

Assuming the pulley is a uniform disk with a mass of 0.31 {rm kg}, find the speed of the block after it has fallen through a height of 0.50 {rm m}.

  Calculate the longitudinal engineering strain

A paper clip is made of wire 0.7 mm in diameter. If the original material from which the wire is made is a rod 25 mm in diameter, calculate the longitudinal engineering strain and true strain that the wire has undergone during processing.

  Determine the magnitude t of the applied torque

The tank has a 180 mm inside diameter and a 12 mm wall thickness. Knowing that the tank contains compressed air under a pressure of 8 MPa, determine the magnitude T of the applied torque for which the maximum normal stress in the tank is 75 MPa.

  Compute the power required to overcome the skin

Calculate the power required to overcome the skin friction drag on the keel of a sailing dingy moving through water at 2m/s. The keel projects 0.8m into the water and it is 0.4m wide

  The system on site is a pressure sand filter with a service

the system on site is a pressure sand filter with a service curve. the filter is backwashed using the feed pump at a

  Calculates and displays the reaction and member forces

Determines if the member forces are in tension or compression (note that a negative number denotes compression and a position number denotes tension)

  Find the horizontal lead to hit the target

The total time it takes to fall is 37 seconds. Find the horizontal lead to hit the target.

  Assuming the center-to-center distance of two atoms not

under a stress of 1105 mpa a sample of ag has a modulus of elasticity of 580 gpa. assuming the center-to-center

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd