A natural gas-fired boiler in a textile plant in sharjah is

Assignment Help Mechanical Engineering
Reference no: EM13628456

A natural gas-fired boiler in a textile plant in sharjah is used to provide steam at 130oC. At times of high demand, the boiler supplies heat to the steam at a rate of 30 MJ/s. The plant also uses up to 6 MW of electrical power purchased from SEWA (the local power company). The plant management is considered converting the existing process plant into a cogeneration plant to meet both their process-heat and power requirements. Your job is to come up with some designs. Designs based on a gas turbine or steam turbines are to be considered. First decide whether a system based on a gas turbine or a steam turbine will best serve the purpose, considering the cost and the complexity. Then propose your design for the cogeneration plant complete with pressure and temperatures and the mass flow rates. Show that the proposed design meets the power and process-heat requirements of the plant.

Reference no: EM13628456

Questions Cloud

A blower handles 1 kgsec of air at 20 deg c and consumes a : a blower handles 1 kgsec of air at 20 deg c and consumes a power of 15 kw. the inlet and outlet velocities of air are
How large of a sample n would you need to estimate p with : how large of a sample n would you need to estimate p with margin of error 0.01 with 95 confidence? use the guess p0.05
If a 43 m steel bridge experiences extreme temp between : if a 43 m steel bridge experiences extreme temp between -11c and 44c what is the range in size of this bridge if it
Suppose that a nickel filter is required to produce an : 1. graphically verify moseleys law for the k beta1 lines of cu mo and w.2. acalculate the mass an linear absorption
A natural gas-fired boiler in a textile plant in sharjah is : a natural gas-fired boiler in a textile plant in sharjah is used to provide steam at 130oc. at times of high demand the
A coil of nichrome wire p156x10-6 ohmm is 30 m long the : a coil of nichrome wire p1.56x10-6 ohmm is 3.0 m long. the radius of the wire is r.25mm. if the wire carries current
Kerosene having a specific weight of 50 lbft3 is flowing : kerosene having a specific weight of 50 lbft3 is flowing at 10 galmin from 1inch pipe to a 2 in pipe. calculate the
The system is under both mechanical and thermal equilibrium : consider a container of volume 250 ml that is divided into two compartments of equal size. in the left compartment
A company is studying the number of monthly absences among : a company is studying the number of monthly absences among its 125 employees. the following probability distribution

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Draw the shear force diagram for the beam

Draw the shear force diagram for the beam and determine the position and magnitude of the maximum bending moment.

  Landing gear system structural design

Problem Statement Consider the landing gear shown below. Working in teprns of two, come up with a single optimized design for given operational conditions and design considerations

  Find the highest cycle pressure

Use cold air properties to find the highest cycle pressure, the specific energy added by combustion, and the mean effective pressure.

  An air-conditioner with refrigerant 134a as the working

an air-conditioner with refrigerant 134a as the working fluid is used to keep a room at 26 c by rejecting the waste

  Wat is the pressure bar at the highest and lowest points

if the atmospheric pressure is 1.025 bar at a location where you can dive in a lake to 30ft below the surface and then

  Calculate the heat emitted to the environment btusec the

a 600 mw coal-fired power plant has an overall thermal efficiency of 38. it is burning coal that has a heating value of

  A 12-mm-diameter specimen is subjected to tensile loading

a 12-mm-diameter specimen is subjected to tensile loading. the increase in length resulting from a load of 9 kn is

  The plate is subjected to an axial force of 75 kn the

the a-36 steel plate has a thickness of 12 mm and other dimensions. r30mm p60mm ab200mm bc800mm cd200 width120mm. the

  How many photons-water interactions occur in one second in

a beam of 2-mev photons with intensity 108 cm-2s-1 irradiates a small sample of water. a how many photons-water

  The tank is allowed to exchange heat with the surroundings

a tank of compressed air is at 40 degrees c and 10 atm. 1 third of the gas is removed for inflating a car tire. the

  Consider an investment in a project having a first cost of

consider an investment in a project having a first cost of 500000 operating and maintenance costs of 35000 per year a

  Determine the distance it travels before it starts

determine the time it takes for the ball to start rolling without slip and its speed when it does so. In addition, determine the distance it travels before it starts rolling without slip. Assume (mu)K = 0.10.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd