User Account

All Pages

A motor consumes 1200 hp of electrical power when operating

Assignment Help Mechanical Engineering
Reference no: EM13624801

A motor consumes 1200 hp of electrical power when operating at steady state. The motor receives an input voltage of 560 VDC (DC stands for direct current).

Find

a) The steady state electrical current used by the motor (A). 1598 A

b) The electrical work consumed by the motor if it operates at steady state for 30 min (kWh), (Btu) 447.4 kWh, 1.527x106 Btu.

Reference no: EM13624801

Questions Cloud

The international space station orbits the earth at an : the international space station orbits the earth at an average altitude of 362 km. assume that its orbit is circular
The composite beam is made of a-36 steel a bonded to c83400 : the composite beam is made of a-36 steel a bonded to c83400 red brass b and has the cross section shown. if it is
Using a finite-difference method with a space increment of : a straight fin of uniform cross section is fabricated from a material of thermal conductivity 50 wmk thickness w6mm and
An object is placed 15 cm from first converging lens of : an object is placed 15 cm from first converging lens of focal length 10 cm.a. a second converging lens with focal
A motor consumes 1200 hp of electrical power when operating : a motor consumes 1200 hp of electrical power when operating at steady state. the motor receives an input voltage of 560
A manufacturer makes 7900000 memory chips per year each : a manufacturer makes 7900000 memory chips per year. each chip takes 0.4 minutes of direct labor at 8hr. the overhead
A clinical trial is conducted to compare an experimental : a clinical trial is conducted to compare an experimental medication to placebo to reduce the symptoms of asthma. two
The structural engineering design section within the : the structural engineering design section within the engineering department of a regional natural gas corporation has
Before heating measurements indicate the volume in the : r-134a is loaded into a weighted pistoncylinder unit. the mass of refrigerant is 10 kg. before heating measurements

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Define a hemispherical dome is filled with water

A hemispherical dome is filled with water. The dome arrangement weighs 28kN and is fastened to the floor by bolts equally spaced

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  Determine the mass flow rate of condensor cooling water in

water is the working fluid in an ideal rankine cylce. saturated vapors enters the turbine at 16mpa and the condensor

  How many positive impulses will be counted per second

A magnetic pickup is used to detect the shaft speed of a turbocharger. A standard hexagonal nut is used to excite the pickup. If the shaft is turning at 50,000 rpm, how many positive impulses will be counted per second?

  Determine the volume required to store 25kg of ethane at

determine the volume required to store 25kg of ethane at 320kpa and 35 degrees celsius. if the temperature rises to 65

  What is the actual mechanical advantage of the system

a first class lever in static equilibrium has a 50lb resistance force and a 15lb effort force. the levers effort force is located 4ft from the fulcrum. what is the actual mechanical advantage of the system?

  A load of lumber of weight w 25 kn is being raised by a

a load of lumber of weight w 25 kn is being raised by a mobile crane. knowing the tension is 25 kn in all portions of

  Find the lowest critical speed of the shaft if the goal is

a 25 mm diameter uniform steel shaft is 600 mm long between bearings.a find the lowest critical speed of the shaftb if

  If the cold-air assumptions can be applied determine how

a four cylinder two stroke diesel engine has a cut-off ratio of 1.8 and a compression ratio of 22. it operates with an

  Determine each of the following a pressure at the end of

a carnot power cycle operates on 1.5 kg of air between the limits of 400 k and 250 k completing one cycle each second.

  Determine the normal stress in the central portion of link

a link AC has uniform rectangular cross section 3mm thick and 25mm wide. Determine the normal stress in the central portion of that link? solution

  What volume must be provided in a methane tank to hold

what volume must be provided in a methane tank to hold 10kg of methane at 1500 kpa and 30 degrees celsius? if the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd