A jet of water leaves the nozzle at the end of a hose the

Assignment Help Mechanical Engineering
Reference no: EM13630723

A jet of water leaves the nozzle at the end of a hose. The area and absolute pressure inside the hose are A1 and p1 and the area and absolute pressure of the jet leaving the nozzle are A2 and p2. The absolute air pressure is atmospheric pressure. A control volume for the nozzle is shown with dotted lines. What is the correct statement for the net forces exerted by the pressure on the control volume?

Reference no: EM13630723

Questions Cloud

A patent application describes a device that at steady : a patent application describes a device that at steady state receives a heat transfer at the rate 1 kw at a
A uniform piece of aluminium is 4m by 4m and 2cm thick a 1m : a uniform piece of aluminium is 4m by 4m and 2cm thick. a 1m by am square piece is cut out from it. the center of the
Develop expressions for the work and heat transfer in terms : a fixed mass of water m initially a saturated liquid is brought to a saturated vapor condition while its pressure and
A 0452 kg block of ice is compressed a distance of 013 m : a 0.452 kg block of ice is compressed a distance of 0.13 m against a spring with a spring constant of 378 nm and is
A jet of water leaves the nozzle at the end of a hose the : a jet of water leaves the nozzle at the end of a hose. the area and absolute pressure inside the hose are a1 and p1 and
A cylindrical graphite pure carbon rod of length 25 cm and : a cylindrical graphite pure carbon rod of length 25 cm and initial diameter of 2 cm is inserted into a flowing air
A 457 kg girl is standing on a plank that has a mass of 152 : a 45.7 kg girl is standing on a plank that has a mass of 152 kg. the plank originally at rest is free to slide on a
Air and rolling resistance of the car may be neglected find : a dragster weighing 7120n attains a speed of 430km in the quarter mile.immediately after passing through the timing
A fabry-perot cavity is made from a 100 cm- tick slab of : a fabry-perot cavity is made from a 1.00 cm- tick slab of germanium with index of refraction 4.02. find the finesse

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find the velocity of the wind

A plane can fly 305 mph in still air. If it can fly 185 miles downwind in the same amount of time it can fly 120 miles upwind, find the velocity of the wind.

  The block is subjected to a compressive force of 2kn

the block is subjected to a compressive force of 2kn. determine the average normal and average shear stress developed

  While flowing through the blower the air temperature can

air is constantly being recirculated throughout the me building. in the summer that air is also cooled using chilled

  This allows the free-stream velocity to remain constant at

a wind tunnel has a 1-m2 6-m-long test section in which air at standard sea-level conditions moves at 70 ms. it is

  What is the specific heat of air in us customary units

what is the specific heat of air in US customary units given that its value in SI units is approximately 1 kN.m/kg.K?

  Show that maximum stored kinetic energy per unit mass of

for a spinning solid circular disk of radius a and constant thickness the maximum stresses occur at thenbspcenter of

  Compute the value of the corrosion potential how long do

lead experiences corrosion in an acid solution according to the following reaction pb 2h rightarrow pb2 h2 the rates

  A special high pressure u-tube manometer is constructed to

a special high pressure u-tube manometer is constructed to measure pressure differential in air at 13.8mpa and 20 c

  Determine the time taken for the product to freeze if it is

a fruit juice containing 30 solids of molecular weight 100 g was placed in a tray length 100 cm height 90 cm width 8

  Find the temperature of source and sink

a heat engine working on carnot cycle converts 25% of heat into work when the temperature of the sink is reduced by 353 k the efficiency gets doubled .find the temperature of source and sink.

  What is the required diameter of the model elbow to

the pressure drop between the entrance and exit of a 150 mm diameter 90deg elbow through which ethyl alcohol at 20degc

  Determine how long it takes to increase the speed of the

a 30-ton engine exerts a constant horizontal force of 40103-lb on a train having three cars that have a total weight of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd