A hydroponic garden uses the 10 m long perforated pipe

Assignment Help Mechanical Engineering
Reference no: EM13627099

A hydroponic garden uses the 10 m long perforated pipe system to deliver water at 20ºC. The pipe is 5cm in diameter and contains a circular hole every 20 cm. A pump delivers water at 75 kPa (gage) at the entrance, while the other end of the pipe is closed. pressure near the closed end of the perforated "manifold" is surprisingly high and there will be too much flow trough the holes near that end. One remedy is to vary the hole size along the pipe axis. Make a design analysis to pick the optimum hole-size distribution that will make the discharge flow rate as uniform as possible along the pipe axis. You are constrained to pick hole sizes that correspond only to commercial metric drill-bit sizes available to the typical machine shop.

Reference no: EM13627099

Questions Cloud

A single-pane glass window is used in a heated dwelling : a single-pane glass window is used in a heated dwelling. outside the dwelling the ambient temperature is 0degc while
Find the correlation coefficient using this to predict the : given the following data setx 1 3 7 9 13 15y 1 5 8 10 11 13a. find the correlation coefficient.b. using this to predict
A stainless steel tube of 1 cm outer diameter and 1mm wall : a stainless steel tube of 1 cm outer diameter and 1mm wall thickness receives a uniform radiative heat flux of 100 wcm2
Apparently low-scoring students on the midterm do better on : in a certain class midterm score average out 60 with an sd of 15 as do scores on the final. the correlation between
A hydroponic garden uses the 10 m long perforated pipe : a hydroponic garden uses the 10 m long perforated pipe system to deliver water at 20ordmc. the pipe is 5cm in diameter
According to the internal revenue service the mean tax : according to the internal revenue service the mean tax refund for the year 2007 was 2708. assume the standard deviation
Using cylindrical coordinates find the canonical : consider a system that consists of a rigid body in three-space with on point fixed. using cylindrical coordinates find
Use the definition of random selection of points in an : use the definition of random selection of points in an interval in section 1.7 a bus arrives at a station everyday at a
A disk of mass m and radius r starts form rest at the top : a disk of mass m and radius r starts form rest at the top of a 30 degree incline with a height of 2m. if the disk rolls

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd