A house wall consists of 12 in drywall 3 58 in glass fiber

Assignment Help Mechanical Engineering
Reference no: EM13641756

A house wall consists of 1/2 in. drywall, 3 5/8 in. glass fiber insulation, and an outside brick wall 4 in. thick. Assume that there is perfect contact between each layer. The thermal conductivities of drywall, glass fiber, and brick are 0.17, 0.036, and 0.72W m^-1 K^-1, respectively. the inside temperature of the house is 70 degrees F; the outside air temperature is 0 degrees F.

A) Find the heat flux in Btu ft^-2 h^-1.

B) Find the temperature (K) at the junction between the drywall and the glass fiber insulation.

C) Find the location (in inches from the inside surface of the drywall) where moisture freezes.

Reference no: EM13641756

Questions Cloud

Discuss the validity of the use of the semi-infinite case : a bar of steel 10 cm x 10 cm x 100 cm has an initial carbon content of 7.6 x 10-3 gmcm3. at t0 the surface of the bar
A box contains 24 yellow 32 green and 36 red jelly beans if : a box contains 24 yellow 32 green and 36 red jelly beans. if 15 jelly beans are selected at random what is the
Plate 3 moves at 3 m s-1 find the velocity of plate 2 at : three parallel flat plates are separated by two fluids. plate 1 on the bottom is at rest. water viscosity 0.8007 cp at
A runner travels 100 m in 104 s assume that it takes him : a runner travels 100 m in 10.4 s. assume that it takes him 1.40 s to reach his top speed which is then maintained for
A house wall consists of 12 in drywall 3 58 in glass fiber : a house wall consists of 12 in. drywall 3 58 in. glass fiber insulation and an outside brick wall 4 in. thick. assume
Given the returns and probabilities for the three possible : given the returns and probabilities for the three possible states listed here calculate the covariance between the
If a typical pad is 50cm thick and compresses by 20cm : falls resulting in hip fractures are a major cause of injury and even death to the elderly. typically the hips speed at
Identify three situations where the measured output of a : identify three situations where the measured output of a process has a small variation and three situations where the
Why when dealing with two independent samples where you : why when dealing with two independent samples where you cannot assume the population variances are equal should the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd