A hot water stream at 80o c enters a mixing chamber with a

Assignment Help Mechanical Engineering
Reference no: EM13625756

A Hot water stream at 80o C enters a mixing chamber with a mass flow of 0.5 Kg/s where it is mixed with a stream of cold water at 20o C. If it is desired that the mixture leave the chamber at 42oC, determine the mass flow rate of the cold-water stream. Assume all the streams are at a pressure of 250 KPa.How do you work it out. The answer is 0.865 Kg/s

Reference no: EM13625756

Questions Cloud

The fluid viscosity u at any point in the boundary layer : the fluid viscosity u at any point in the boundary layer depends on the distance y of the point above the surface the
At what distance must the cheetah relative to the antelope : zoologists estimate that the average adult cheetah can run at a speed of 100 kmhr and that the average antelope can run
Show that the moment of inertia of the object about its : the period t of a physical pendulum is measured about a certain pivot point a. the measurement is repeated varying the
A motorist decreases the speed of an automobile at a : a motorist decreases the speed of an automobile at a constant rate from 45 to 30 mih over a distance of 750 ft along a
A hot water stream at 80o c enters a mixing chamber with a : a hot water stream at 80o c enters a mixing chamber with a mass flow of 0.5 kgs where it is mixed with a stream of cold
Suppose that 50007 nearly half of the electrons have a : a block of iron with volume 18.5 times 10-5 m3 contains 2.75 times 1025 electrons with each electron having a magnetic
Determine the difference between these values and the : an airplane flying at m0 0.8 under standard sea level conditions has instrumentation embedded at the stagnation point
An adiabatic capillary tube is used in some refrigeration : an adiabatic capillary tube is used in some refrigeration systems to drop the pressure of the refrigerant from the
State the hypothesis of interest and conduct the : a study was conducted to determine if there is a difference between the investing preferences of mid-level managers

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Hazen-williams formula -find the diameter of a pipe

Hazen-Williams Formula- Find the Diameter of a Pipe, The length of cast-iron pipe is to be 4200 ft., and the head causing flow is to be 12.6ft. After the pipe has been in service 5 years, it is expected to discharge water at a rate equal to 3.2 cf..

  What is the outlet pressure if the inlet pressure is 100 mm

for a one order narrowing of arterial vessel in cross sectional area ainaout 10 what is the outlet pressure if the

  Determine a the volume and mass flow rates of water through

a garden hose attached with a nozzle is used to fill a 10-gallon bucket. the inner diameter of the hose is 2 cm and it

  Solar energy reaching the earth is about 1350 wm2 outside

solar energy reaching the earth is about 1350 wm2 outside the earths atmosphere and 950 wm2 on earths surface normal to

  Evaluate the various methods of how safety is measured and

evaluate the various methods of how safety is measured and the current safety data systems and compare and contrast

  R-134a vapor enters an adiabatic turbine at 250 psia and

r-134a vapor enters an adiabatic turbine at 250 psia and 175 f. the temperature at the outlet is 20 f. determine the

  A valve connected to the cylinder is now opened and air is

a vertical piston-cylinder device initially contains 0.25 m3 of air at 600 kpa andnbsp300degc. a valve connected to the

  Calculate the volume flow rate through the turbine m3s what

a pelton wheel is used to produce hydroelectric power. the average radius of the wheel is 1.83 m and the jet velocity

  A boiling-water-type nuclear fission reactor has shut down

a boiling-water-type nuclear fission reactor has shut down the backup pumps have failed and emergency cooling water

  The refrigerant leaves the condenser at 07 mpa 26 degc

consider a non-ideal vapor-compression cycle where refrigerant 134a flows at a rate of 0.05 kgs. the refrigerant enters

  What percentage of the electrons originally in the cube was

suppose a cube of aluminum which is 1.00 cm on a side accumulates anet charge of 2.50 pc. awhat percentage of the

  Calculate the necessary piston displacement in order to

a 3-diameter 5-long gas-piston assembly contains air at stp. stp standard temperature and pressure conditions 300k and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd