A heat pump with refrigerant 134-a as the working fluid is

Assignment Help Mechanical Engineering
Reference no: EM13631813

A heat pump with refrigerant 134-a, as the working fluid is used to keep a space at 25C by absorbing heat from geothermal water that enters the evaporator at 50C at a rate of .065kg/s and leaves at 40C. The refrigerant enters the evaporator at 20C with a quality of 23% and leaves at the inlet pressure as saturated vapor. The refrigerant loses 300W of heat to the surroundings as it flows through the compressor and the refrigerant leaves the compressor at 1.4MPa at the same entropy as the inlet.

Determine ;
A) the degrees of subcooling of the refrigerant in the condenser
B) the mass flow rate of the refrigerant,
C)the heating load and COP of the heat pump
D) the theoretical minumim power input to the compressor for the same heating load.

Reference no: EM13631813

Questions Cloud

A judge chooses a jury of n people out of a pool of n : a judge chooses a jury of n people out of a pool of n people. the choice is uniform among all subsets of n elements of
An orifice meter is to be installed in a 12-in ductile iron : an orifice meter is to be installed in a 12-in ductile iron pipe carrying water at 60degf. a mercury manomoter is to
Neglecting the kinetic and potential energy changes between : steam enters a compressor operating at steady state at 250 degrees farenheit 14.7 lbfin2 and exits at 400 degrees
A 10-cm-diameter parallel-plate capacitor has a 10 mm : a 10-cm-diameter parallel-plate capacitor has a 1.0 mm spacing. the electric field between the plates is increasing at
A heat pump with refrigerant 134-a as the working fluid is : a heat pump with refrigerant 134-a as the working fluid is used to keep a space at 25c by absorbing heat from
Air an ideal gas contained in a rigid insulated tank fitted : air an ideal gas contained in a rigid insulated tank fitted with a paddle wheel initially at 27 degrees celcius 2 bar
Consider a front loader washer that weighs 200 lb with a 6 : consider a front loader washer that weighs 200 lb with a 6 lb towels. the size of the drum is 0.4 m. during a spin
A particle is trapped in an infinite square well in the : a particle is trapped in an infinite square well in the first excited state .a what is the wavefunction of the
The average temperature of the stream passing through the : a power cycle operating at steady state has a thermal efficiency of 35 and generates 100 mw of electricity while

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  You decide to do a demonstration on a rooftop that requires

you decide to do a demonstration on a rooftop that requires water. there isnt a handy faucet so you put a barrel of

  What is the heat rejection for the condenser in btuh if the

consider a small simple rankine power cycle which produces 600kw power from an electric generator with an efficiency of

  A 40 foot long aluminum street lighting support is sized

a 40 foot long aluminum street lighting support is sized and welded into position between two very large bridge beams

  An isentropic steam turbine processes 5kgs of steam at 4mpa

an isentropic steam turbine processes 5kgs of steam at 4mpa. the majority of this steam is exhausted at 50kpa and 100

  Determine the rate of heat transfer to the mid-stage

Determine the rate of heat transfer to the mid-stage cold head and determine the rate of heat transfer to the cold head

  After 10 lbhr of the oil is removed from the potato chips

after 10 lbhr of the oil is removed from the potato chips in the separation unit what is the mass fraction of oil on

  Show the principle stresses on the neutral axis

Show the principle stresses on the neutral axis on a correctly oriented element relative to the axis of the beam.

  A light truck weighs 3100 lb and is rated at 30 miles per

a light truck weighs 3100 lb and is rated at 30 miles per gallon for a 60 mph highway driving on level ground. how much

  Air conditioning1- cooling and heating load estimate using

air conditioning1- cooling and heating load estimate using camel program library and the data from da-9 perform a

  Observing plastic deformationthe aim of this demonstration

observing plastic deformationthe aim of this demonstration is to make some observations of the surface relief produced

  Air can be assumed to be an ideal gas with a

a well-insulated tank contains 1 mole of air at 2 mpa and 673 k. it is connected via a closed valve to an insulated

  Find the time it took for his voice to reach the earth via

neil a. armstrong was the first person to walk on the moon. the distance between the earth and the moon is 3.85 108 m.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd